manualshive.com logo in svg

Cedar Summit WESTBURY F25030, Installation And Operating Instructions Manual

Share
Download
Cedar Summit WESTBURY F25030 Installation And Operating Instructions Manual Download Page 17

 

17 

[email protected]

12 x 

#8 x 1-1/16” Wood Screw

6 x 

1/4” T-nut

Step 2: Side Wall Prep 

Part 1

It is important to assemble the frame on a flat, smooth surface.

A:

  Place (2771) End Post and (2770) End Post Left side by side with the grooves facing up and in.  (2770) End 

Post Left on the right hand side.  Place (2769) Panel BT Frames in the top and bottom grooves and (2768) Panel 

Floor in the middle grooves.  (fig. 2.1)

B:

  Make sure assembly is square then attach with 4 (S30) #8 x 1-1/16” Wood Screws per board.  (fig. 2.1) 

C:

  Tap in 2 (TN1) 1/4” T-nuts in (2768) Panel Floor and each (2769) Panel BT Frame.  (fig. 2.1 and 2.2) 

1 x 

Panel Floor 1-1/4 x 3 x 42”

2 x  

Panel BT Frame 1-1/4 x 3 x 42”

1 x 

End Post 1-1/4 x 2-1/2 x 87”

1 x 

End Post Left 1-1/4 x 2-1/2 x 87”

S30

2768

Wood Parts

Hardware

2771

2770

2769

Fig. 2.2

Fig. 2.1

Bottom

Top

2770

2771

S30

x 4

Flush

Flush

Flush

S30

x 4

S30

x 4

2768

2769

2769

TN1

TN1

TN1

x 2

TN1

TN1

TN1

TN1

Summary of Contents for WESTBURY F25030





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands