CD3 Outpost Product Manual Download Page 17 | Manualshive

Page: 17 / 56

CD3 Outpost Product Manual Download Page 17

CD3 Products Manual

CD3, General Benefit Corporation |

www.cd3station.com

[email protected]

| 612.467.9441

Patent

Pending | Made in USA | © 2019

17

Section 3 – Unit Operation

3.1 Main Power Shut-Off Switch

The Unit is equipped with a master power shut-off switch that removes any current
draw from the system.  The switch is located inside the rear service door and mounted
to the electrical component plate straight inside.  The switch has about a three inch
diameter dial.  Turn the switch clockwise to apply power and counter-clockwise to
disconnect power. This switch should be disengaged before any maintenance or repairs
are performed on the unit.

*Wayside and Outpost Units Note: The shut-off switch still needs to be in the “On”
position to be able to charge the batteries either by solar means (Wayside Solar and
Outpost) or by battery charger (Wayside 120V).

Station

Wayside

Outpost

3.2 All Off Button (Station/Wayside Only)

The All Off button is to cancel all functions of the unit at
any time during their use. This is to be used in any scenario
where the functions need to be interrupted. Pushing this
button will cancel any timer of an operation and cancel its
operation immediately. The actuation button for any of the
functions can be pushed right away again to turn them back
on if desired, but the timer for the function will start over.
It is important to note that this button does not cancel
power to the machinery for servicing, it only shuts down
any active function for the user’s perspective.

«
...
15
16
17
18
19
...
»

Summary of Contents for Outpost

























































Reviews:

No comments