CD3 Outpost Product Manual Download Page 16 | Manualshive

Page: 16 / 56

CD3 Outpost Product Manual Download Page 16

CD3 Products Manual

CD3, General Benefit Corporation |

www.cd3station.com

|

[email protected]

| 612.467.9441

Patent

Pending | Made in USA | © 2019

16

1.

Practice safety requirements. Stay alert, have proper attire, and do not operate tools
under the influence of alcohol or drugs.

2.

Always inspect equipment for damage prior to use. Loose hoses or fittings can
create dangerous situations.

3.

Always wear ANSI-approved safety goggles when working with tools and equipment.

4.

Do not modify any part of the unit to perform any task for which they were not
intended as described in this manual.

5.

Never point the blow gun or blow compressed air at peoples or animals.

6.

Do not allow to be used as a toy. Close attention is necessary when used by or near
children.

7.

Use only as described in this manual.

8.

Do not use with damaged cord or plug. If the unit is not working as it should or has
been damaged, contact CD3 for assistance.

9.

Keep power cord away from heated surfaces.

10.

Do not unplug by pulling on cord. To unplug, grasp the plug; not the cord.

11.

Do not handle plug with wet hands.

12.

Do not use with any openings blocked; keep free of dust, lint, and anything that may
reduce air flow. Do not place or store anything to block cooling air intake or exhaust
of openings on the unit. Component damage may result.

13.

Keep hair, loose clothing, fingers and all parts of body away from openings and
moving parts

.

14.

The tools are intended to be operated as a hand held tools. It is always
recommended that while using the tools, operators stand on solid ground, in a
secure position with a firm grip and footing.

15.

Turn off main shut-off switch before unplugging.

16.

Danger - DO NOT allow tool cables to retract in an uncontrolled manner. Always
guide cable back to reel. Failure to do so can result in damage to reel or personal
injury.

«
...
14
15
16
17
18
...
»

Summary of Contents for Outpost

























































Reviews:

No comments