background image

18

OPERATING YOUR STAND MIXER KM 8020

ATTENTION:
If you are going to process solid 
mixtures such as bread doughs, do 
not run the stand mixer for more 
than 10 minutes. Then, turn the stand 
mixer off and let it cool down for 
about 10 minutes.

ADJUSTING THE WHISK

You can adjust the whisk so that it is placed 
lower or higher in the container so you can 
easily whisk the ingredients.

WARNING!
Always adjust 
the whisk when 
removing it from 
the shaft. The 
whisk must not be 
mounted on the 
shaft.

The whisk can be unscrewed or screwed at 
the top of the whisk.
If you need the whisk to be placed higher in 
the container, turn the screw clockwise.

If you need the whisk to be placed lower in 
the container,turn it counter-clockwise.
Check the position of the whisk by attaching 
it to the shaft and adjusting it if necessary.

NOTE
The kneading hook and fl at beater 
are factory set to the optimum height 
in the container. They cannot be 
adjusted.

ATTENTION:
Be careful not to unscrew or screw 
the screw too much - it could fall out 
of the whisk. In addition, if you screw 
the screw too much, it may interfere 
with the whisk on the shaft when it is 
properly seated.

SAFETY FEATURES

If you plug the power cord into a power 
outlet while the speed control is set to 
a certain speed, the food processor will not 
start and the light will fl ash. Disconnect the 
power cord from the power socket and set 
the control knob to "0".
If you lift the arm while the food processor is 
running, the food processor will turn off  and 
the light will go out. If the arm is lowered, the 
light will fl ash. Turn the speed dial to “0” and 
then select the speed again.
If the engine overheats, the food processor 
will automatically shut down and the light 
will fl ash. Turn the control to “0”, disconnect 
the power plug from the power outlet, and 
allow it to cool.

Summary of Contents for KM 8020




























Reviews: