CAR-5040 Series User’s Manual
頁
95
■ 5.5.4 vKVM application settings
This section will describe those setting on the menu bar as
Fig. 5.5.7
show.
File:
Capture to File:
To capture an image, click
Capture to File
from the File menu. A dialog box is
displayed that allows user to save the file to a specified location.
Exit:
Select
Exit
to close the viewer.
View:
Hide Status Bar:
To show/hide the addition information bar below the vKVM application, click
Hide
Status Bar
from the View menu.
Refresh:
Select
Refresh
to update the view of the Video Viewer. This will result the Viewer
requesting a reference video frame from the server.
Full Screen/Windowed:
Select
Full Screen
to make the Video Viewer enter into Full Screen Mode. Select
Windowed
to exit out of Full Screen mode.
Fit:
Select
Fit
to resize the Video Viewer window to the minimum size that is need to
display the server's video. (This menu item is not available in Full Screen mode.)
Macros:
Select one of the drop-down list keyboard shortcuts (either the macro or the hotkey
specified for the macro), to execute the macro on the remote system.
Tools:
Session Options:
i.
General:
User can control the keyboard pass-through mode and select
Pass all
keystrokes to target
to pass users’ management station's keystrokes to the
remote system. Some keystrokes are intercepted by the management station
OS and will not be passed on.
ii.
Mouse Acceleration:
To optimize mouse performance, click the
Mouse
tab and depending on the
operating system, select the
Mouse Acceleration
option. Then click
Apply
and
OK
to close the Session Options window. The mouse tab provides Mouse
Acceleration.
iii.
Video Quality:
The compression modes allow for a low quality (420) or high quality (444)
compression configuration. The Luminance and Chrominance settings allow
Summary of Contents for CAR-5040 Series
