Cascade 14J Installation Instructions And Periodic Maintenance Download

Page: 2 / 24

6871082-R2

RECOMMENDED HYDRAULIC SUPPLY

CONTENTS

GA0033.eps

This manual provides instructions for installing Cascade

J-Series Carton Clamps.
Follow the suggested installation procedures for best

results. If you have any questions or need more

information, contact your nearest Cascade Service

Department for assistance. Refer to back cover.
Read the

WARNING

Statements placed throughout

this Manual to emphasize safety during attachment

installation.

IMPORTANT:

Field alterations may impair performance

or capability and could result in loss of warranty.

Consult Cascade for any required modifications.

Recommended Hydraulic Supply

Truck Requirements

Standard Carton Clamp &

White Good Clamps

Tipping Carton Clamp

Installation

Load Troubleshooting

Adjusting Pad Camber

Standard (Shimmed) Design

Flexible (Adjusta-Block) Design

Periodic Maintenance

General

Attachments with External Sideshift

Tipping Attachments

J-Series Clamps provide the best performance with one of the hydraulic

supply arrangements shown below. Refer to Cascade

Hose & Cable Reel

Selection Guide

, Part No. 212199, to select the correct hose reel for the

mast and truck. The hose and fitting requirements are:

• All hoses and fittings for CLAMP and SIDESHIFT functions should be at

least No. 6 (M8) with a minimum internal diameter of 0.28 in. (7 mm).

Non-Sideshifting
A or B

RH or LH THINLINE™ 2-port Hose Reel Group.

Mast single internal hose reeving group.

Sideshifting
A and B

RH and LH THINLINE

™

2-port Hose Reel Groups.

Mast double internal hose reeving group.

Sideshifting with Solenoid
A

6-N-1 Cable/Hose Reel group.

A and C

Cable Reel and single internal hose reeving group.

Summary of Contents for 14J

























Search results

Summary of Contents for 14J

Reviews:

Related manuals for 14J

Brands by name

Popular brands

Cascade 14J, Installation Instructions And Periodic Maintenance

Search results

Summary of Contents for 14J

Reviews:

Related manuals for 14J

Brands by name

Popular brands