Cascade 14J Installation Instructions And Periodic Maintenance Download

Page: 17 / 24

6871082-R2

ADJUSTING PAD CAMBER

STANDARD (SHIMMED) DESIGN

CC0012.eps

Loosen the contact pad capscrews and nuts.

NOTE:

It is not necessary to remove the capscrews

and nuts to insert the shims.

Install shims as required.
•

Positive Camber –

Install shims at the bottom and

middle of the pad to increase clamp force at the

bottom of the load.

NOTE:

This will increase the clamp force

percentages on the lower spindles readout of the

4-Point Force Distribution Tester.

•

Negative Camber –

Install shims at the top and

middle of the pad to decrease clamp force at the

bottom of the load.

NOTE:

This will increase the clamp force

percentages on the upper spindles readout of the

4-Point Force Distribution Tester.

CAUTION:

Use an equal number of shims on each

contact pad. Pad camber must be the same on both

sides of the attachment for proper load handling.

CL5078.eps

"U" Shim

CL0556.ill

Top Shim

Contact Pad

Pad

Capscrews

and Nuts

Arm

Bottom Shim

Stabilizer

Middle Shim

FOR MINIMUM

POSITIVE CAMBER:

FOR MAXIMUM

POSITIVE CAMBER:

Middle Shim:

Long Shim – One Each

0.06 in. (1.6 mm)
"U" Shim –

One Each, 2 Places

0.04 in. (1 mm)

Middle Shim:

Long Shim – Two Each

0.06 in. (1.6 mm)
"U" Shim –

Two Each, 2 Places

0.04 in. (1 mm)

Bottom Shim:

Long Shim – One Each

0.125 in. (3.2 mm)
"U" Shim –

One Each, 2 Places

0.08 in. (2 mm)

Bottom Shim:

Long Shim – Two Each

0.125 in. (3.2 mm)
"U" Shim –

Two Each, 2 Places

0.08 in. (2 mm)

Contact Pad

Camber

Clamp Force Change @

Maximum Shimming

◆

Clamp Force

Distribution

Upper

Lower

Upper

Lower

Neutral

▲

—

35%

65%

Negative

+10%

–10%

45%

55%

Positive

–10%

+10%

25%

75%

▲

Shimmed equally in all locations.

◆

Camber based on 12 mm total shims negative or positive position.

Summary of Contents for 14J

























Search results

Summary of Contents for 14J

Reviews:

Related manuals for 14J

Brands by name

Popular brands

Cascade 14J, Installation Instructions And Periodic Maintenance

Search results

Summary of Contents for 14J

Reviews:

Related manuals for 14J

Brands by name

Popular brands