background image

26

PRODUCT SPECIFICATIONS

Model Name:

 Antion

Model Number:

 C39G199H

Dimensions: 

A =  11.7

 

B =  16.0

 

C =  3.1

 

D = 18.1

 

E =  7.6

Weight: 

22 lbs.

Motor:

 

172

mm

 x 20

mm

 Direct Drive

Blade Span With:

  52"

Blade Pitch:

 

14°

No. of Blades:

  5

Technology: 

W74SL- Direct-Touch

Lightbulbs:

 

50-watt Halogen (2)

 

Airflow:

 

5594 cfm

Electricity Use:

 69 watts

Airflow Efficiency:

 81.4 cfm/watt

Fan_Finishes
•  For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.
•  A vacuum cleaner brush nozzle can remove heavier dust.
•  Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent 

and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning 
agents as these will damage the finish.

Blades
•  Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of 

furniture polish may be applied for added protection and beauty.

•  For painted and high-gloss blades,  surface smudges or an accumulation of dirt and dust can be 

removed easily using a mild detergent and slightly dampened soft cloth. An antistatic agent may be 
used, but never use abrasive cleaning agents as these will damage the finish.

No_Need_for_Lubrication
•  Never lubricate this fan!  The precision motor at the heart of your Casablanca fan features sealed 

bearings that are lubricated for life. 

•  Do not attempt to oil the motor.
Changing_Lightbulbs
•  Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs.
•  Replace bulbs with the same type as you removed from the light fixture. 
•  The maximum wattage rating for this fan’s light kit is 100 watts.

CARE RECOMMENDATIONS

FOR QUESTIONS OR TO LOCATE THE NEAREST CASABLANCA 

AUTHORIZED SERVICE CENTER

CALL TOLL FREE: 1-888-227-2178  

OR VISIT US ON THE WEB AT:  WWW.CASABLANCAFANCO.COM

Summary of Contents for Antion C39G199L















Reviews: