background image

GB - 4

AQUASMART Room Controller

Electrical connections

Wiring Room Controller to the unit

WARNING:
Before connecting any wiring to the Room Controller,
turn off all power to the unit that will supply power to the
Room Controller.
Electrical shock can cause personal injury or death.

The Room Controller is connected to the unit using the
following instructions.
Reference Diagram 1 or 2 when making these connections.

Power cable and communication connections Room
controller to the unit (3 conductor cable).

• Slacken the terminal screws P (DC Power), G (GROUND) and

C (SIGNAL), present on the rear base of the Room Controller.

- P (DC power)
- G (Ground)
- C (Signal)

• Make the connections on the terminal block of the Room

Controller as per diagram 1.

• Connect the other end of the cables to the terminal block of

the unit as per diagram 1.

• Power cable installation is now complete.

• Slacken the terminal screws P (DC Power), G (GROUND)

and C (SIGNAL), present on the rear base of the Room
Controller.

- P (DC power)
- G (Ground)
- C (Signal)

• Make the connections on the terminal block of the Room

Controller as per diagram 2.

• Connect the other end of the cables to the terminal block of

the unit as per diagram 2.

• Power cable installation is now complete.

Wiring Materials required
(supplied by installer)

1 small screwdriver

3 x 0,5  mm

2

 multiple cables, double insulated.

Suggested type: H03VV-F.

Diagram 2:

Connection diagram for the 42Y unit

Wire colours

A

Brown

B

Blue

Y/G Yellow/green

Room Controller

Unit

Terminal block in the Room Controller

Terminal block in the unit

Window contact (if present)

Local Bus; maximum 6 units

Diagram 1:

Connection diagram for the following units:

42GW

42WHC/WHE

42JW

42EL

D.C. POWER

GROUND

(SIGNAL)

P
G
C

7
6
5
4
3
2
1

A

B

Y / G

A

B

Y / G

D.C. POWER

GROUND

(SIGNAL)

P
G
C

5
4
3
2
1

A

B

Y / G

A

B

Y / G

Wire colours

A

Brown

B

Blue

Y/G Yellow/green

Room Controller

Unit

Terminal block in the Room Controller

Terminal block in the unit

Window contact (if present)

Local Bus; maximum 6 units

Summary of Contents for AQUASMART










Reviews: