background image

                                                               ( 1 )

 

1. GENERAL INFORMATION 

 

PRECAUTIONS 

 

Installing and servicing of air conditioning equipment can be hazardous due to system 
pressure and electrical components. Only trained and qualified service personnel should 

install or service this equipment. 

 

Untrained personnel can perform basic maintenance function such as cleaning coil and 
filters. Trained service personnel should perform all other operations

 

When working on air conditioning equipment, observe precautions in the literature, tags 
and labels attached to the unit. 

 

 

WARNINGS 

 

The operating voltage of electrical power supply should be within the voltage mentioned on unit 
nameplate data

 

 

The capacity of electrical kWh counter should be larger than the operating currents required for 
air conditioner(s) and any other electrical domestic appliances in use simultaneously from the 

same supply.

 

 

 

The installation of electrical distribution box after the electrical KWH counter is necessary to 
properly distribute the electrical loads. The electrical distribution box should be equipped with 

circuit breakers according to the electrical loads. For each installed air conditioner, a separate 
circuit breaker with its own overload should be installed on the electrical distribution box.

 

 

 

The installation of two-pole automatic circuit breaker is necessary to operate the air conditioner. 
The circuit breaker must be installed to be far away from any flammable materials (curtains…etc.). 

The circuit breaker size must be suitable for air conditioner.

 

 

 

Disconnect the electrical mains supply prior to any maintenance operations or prior to handling 
any internal unit parts

 

 

The manufacturer declines any liability for damage resulting from modifications or errors in the 

electrical or refrigerant connections, made during the installation, or from the improper use of this 
equipment. This will void the unit warranty immediately.

 

 

 

Failure to observe electrical safety codes may cause a fire hazard in case of short circuits.

 

 

 

This system will only work safety and correctly, if installed and tested by qualified personnel.

 

 

 

Do not open the electronic remote controller to avoid possible damage. In case of malfunction 

contact a qualified service engineer.

 

 

 

The unit contains rotating equipment (fan). Ensure that this is out of reach for children.

 

 

 

Be conscious of the room temperature and general comfort, particularly when this is used near 
children, senior or handicapped people.

 

 

 

For correct use, the air conditioner must operate within the temperature limits indicated in the 
table “Operating Limits” included in the installation manual. Incorrect use of the system outside 

these limits may cause malfunction and dripping water.

 

 

 

Controller batteries contain polluting elements. When exhausted, they must be disposed of in 
accordance with local requirements.

 

 

 

Do not switch off the split system by disconnecting the electric power supply.

  

 

The system must always be switched off using the remote control.

 

Summary of Contents for 53VMCT 18C-24C-30C-36C

































Reviews: