![background image](http://html.mh-extra.com/html/carrier/50hjq004-007/50hjq004-007_installation-start-up-and-service-instructions-manual_2563306003.webp)
3
Step 3 — Install Condensate Drain Line and
External Trap —
Condensate drain connections are locat-
ed at the bottom and side of the unit. Unit discharge connec-
tions do not determine the use of drain connections; either
drain connection can be used with vertical or horizontal dis-
charge units.
When using the standard side drain connection, make sure
the plug (red) in the alternate bottom connection is tight before
installing the unit.
To use the bottom drain connection for a roof curb installa-
tion, relocate the factory-installed plug (red) from the bottom
connection to the side connection. See Fig. 3. The piping for
the condensate drain and external trap can be completed after
the unit is in place.
All units must have an external trap for condensate drain-
age. Install a trap at least 4 in. deep and protect against freeze-
up. If drain line is installed downstream from the external trap,
pitch the line away from the 50HJQ unit at 1 in. per 10 ft of
run. Do not use a pipe size smaller than the unit connection
(
3
/
4
-in.).
Step 4 — Rig and Place Unit —
Inspect unit for
transportation damage, and file any claim with transportation
agency. Keep unit upright and do not drop. Spreader bars are
not required if top crating is left on unit, and rollers may be
used to move unit across a roof. Level by using unit frame as a
reference. See Table 1 and Fig. 4 for additional information.
Operating weight is shown in Table 1 and Fig. 4.
Lifting holes are provided in base rails as shown in Fig. 4
and 5. Refer to rigging instructions on unit.
POSITIONING — Maintain clearance around and above unit
to provide proper airflow and service access. See Fig. 5.
A properly positioned unit will have the following clear-
ances:
1
/
4
-in. clearance between roof curb and base rails on
each side and duct end of unit;
1
/
4
-in. clearance between roof
curb and condenser end of unit. (See Fig. 1, section C-C.)
Do not install unit in an indoor location. Do not locate unit
air inlets near exhaust vents or other sources of contaminated air.
Although unit is weatherproof, guard against water from
higher level runoff and overhangs.
After unit is in position, remove polyethylene shipping
wrapper and top crating.
All panels must be in place when rigging.
MAXIMUM ALLOWABLE
DIFFERENCE (in.)
A-B
B-C
A-C
0.5
1.0
1.0
Fig. 2 — Unit Leveling Tolerances
DRAIN PLUG
CONDENSATE PAN (SIDE VIEW)
NOTE: Drain plug is shown in
factory-installed position.
Fig. 3 — Condensate Drain Connection
(Side View)
NOTES:
1. Dimension in ( ) is in millimeters.
2. Hook rigging shackles through holes in base rail, as shown in detail
‘‘A.’’ Holes in base rails are centered around the unit center of grav-
ity. Use wooden top skid when rigging to prevent rigging straps
from damaging unit.
3. Unit weights do not include economizer. See Table 1 for econo-
mizer weights.
All panels must be in place when rigging.
UNIT
OPERATING
WEIGHT
DIMENSIONS
‘‘A’’
‘‘B’’
‘‘C’’
lb
kg
in.
mm
in.
mm
in.
mm
50HJQ004
500
227
73.69 1872 35.50
902
33.31
847
50HJQ005
550
249
73.69 1872 35.50
902
33.31
847
50HJQ006
590
268
73.69 1872 35.50
902
33.31
847
50HJQ007
610
277
73.69 1872 35.50
902
33.31
847
Fig. 4 — Rigging Details
Summary of Contents for 50HJQ004-007
Page 42: ...42 Fig 43 Typical Wiring Schematic 50HJQ006 007 Shown ...
Page 43: ...43 Fig 43 Typical Wiring Schematic 50HJQ006 007 Shown cont ...
Page 45: ......
Page 47: ......