![background image](http://html1.mh-extra.com/html/carrier/48gc04/48gc04_service-and-maintenance-instructions_2560987008.webp)
8
NOTE: Values in the Field Accessories section are RPM adders.
Fig. 11 — Example of Fan Speed Set Up Labels for SystemVu™ Controls
TROUBLESHOOTING THE ECM MOTOR
EcoBlue™ motors are designed with several built-in protections
included in the motor software. If the motor detects a fault it will
safely shut down. For temperature related faults the motor re-
quires a line voltage reset to continue operation. For all others,
the motor will resume operation automatically as soon as the
fault condition is cleared. See Table 3 for a complete list.
Table 3 — Fault Condition/Reset Trigger
Troubleshooting the motor requires a voltmeter.
1. Disconnect main power to the unit.
2. Disconnect motor plug in supply section of the unit.
3. Restore main unit power.
4. Check for proper line voltage at motor power leads Black
(PL1-1), Yellow (PL1-2), and Blue (PL1-3). Blue is only
present on 3-phase motors. See the following table.
5. Disconnect main power.
6. Reconnect motor plug in supply section of unit.
7. Restore main power.
8. Check for proper motor control voltage signal of 9.7Vdc to
10.3Vdc at IFM-1 and IFM-3 on Unit Control Board (UCB).
See Fig.12 for 3 phase units and see Fig. 13 for 1 phase units.
9. Using a jumper wire from unit control terminals R to G,
engage motor operation.
10. Verify control signal from user speed selection switch by
placing voltmeter taps in provided terminals marked Vdc.
Signal should be between 3.8Vdc and 10.3Vdc.
11. If the motor does not start and run, remove the fan assem-
bly and replace the motor with one having the same part
number. Do not substitute with an alternate design motor
as the voltage/speed programming will not be the same as
that on an original factory motor.
Field Accessories:
2500
Economizer
ESP in. wg
RPM
Calculator
CFM
0.2
1425
1512
1601
1692
1784
1878
1973
2069
2166
1500
1625
1750
1875
2000
2125
2250
2375
65
0.4
1609
1688
1768
1850
1933
2018
2104
2192
2282
65
0.6
1764
1839
1916
1994
2073
2153
2235
2317
0.8
1902
1974
2047
2123
2200
2277
2356
65
1.0
2028
2097
2168
2241
2316
65
1.2
2147
2212
2280
2351
65
1.4
2260
2322
2387
65
1.6
1.8
2.0
2367
65
65
UNIT MODEL
NUMBER
Fault
Condition
Reset
Trigger
Description
Phase Failure
Automatic
One phase is missing or imbalanced. In
this case the motor will come to a stop
and then automatically restart when all
phases are present.
Locked/ Blocked
Rotor
Automatic
The rotor is blocked. Once the locking
mechanism has been removed, the
motor will automatically restart.
Motor Over
Heated
Manual
The motor will stop in the event the
motor over heats. In this case there has
to be a manual restart.
Power Module
Over Heated
Manual
The motor will stop in the event the
electronics over heat. In this case there
has to be a manual restart.
Line under-
voltage
Automatic
Once the line voltage returns within
permitted operating range, the fan will
automatically restart.
Communication
Error
Automatic
Internal communication error of the
fan’s electronics. The fan will restart
automatically, if error is cleared.
48GC Unit Voltage
Motor Voltage
Min-Max Volts
208/230
230
187-253
460
460
360-506
575
575
517-633
Summary of Contents for 48GC04
