![background image](http://html1.mh-extra.com/html/carrier/48gc04/48gc04_service-and-maintenance-instructions_2560987032.webp)
32
GAS VALVE
All three-phase models (except Low NOx) are equipped with 2-
stage gas valves. Single-phase models and all Low NOx models
are equipped with single-stage gas valves. See Fig. 56 for loca-
tions of adjustment screws and features on the gas valves.
To adjust gas valve pressure settings:
CHECK UNIT OPERATION AND MAKE NECESSARY
ADJUSTMENTS
NOTE: Gas supply pressure at gas valve inlet must be within
specified ranges for fuel type and unit size. See Tables 9 and 10.
1. Slide out burner partition panel.
2. Remove manifold pressure tap plug from manifold and
connect pressure gage or manometer. (See Fig. 53.)
3. Turn on electrical supply.
4. Turn on unit main gas valve.
5. Set room thermostat to call for heat. If unit has two-stage
gas valve, verify high-stage heat operation before attempt-
ing to adjust manifold pressure.
6. When main burners ignite, check all fittings, manifold,
and orifices for leaks.
7. Adjust high-stage pressure to specified setting by turning
the plastic adjustment screw clockwise to increase pres-
sure, counter-clockwise to decrease pressure.
8. For two-stage gas valves, set room thermostat to call for low-
stage heat. Adjust low-stage pressure to specified setting.
9. Replace regulator cover screw(s) when finished.
10. Observe unit heating operation in both high stage and low
stage operation if so equipped. Observe burner flames to
see if they are blue in appearance, and that the flames are
approximately the same for each burner.
11. Turn off unit, remove pressure manometer and replace the
manifold pressure tap plug. (See Fig. 51.)
LIMIT SWITCH
Remove blower access panel. Limit switch is located on the
fan deck. See Fig. 47.
Burner Ignition
Unit is equipped with a direct spark ignition 100% lockout sys-
tem. The Integrated Gas Unit Controller (IGC) is located in the
control box (see Fig. 54). The IGC contains a self-diagnostic
LED (light-emitting diode). A single LED (see Fig. 57) on the
IGC provides a visual display of operational or sequential prob-
lems when the power supply is uninterrupted. When a break in
power occurs, the IGC will be reset (resulting in a loss of fault
history) and the indoor (evaporator) fan ON/OFF times will be
reset. The LED error code can be observed through the viewport.
During servicing, refer to the label on the control box cover or Ta-
ble 11 for an explanation of LED error code descriptions.
If lockout occurs, unit may be reset by interrupting power sup-
ply to unit for at least 5 seconds.
Orifice Replacement
This unit uses orifice type LH32RFnnn (where “nnn” indicates
orifice reference size). When replacing unit orifices, order the
necessary parts through RCD. See the High Altitude Gas Con-
version Kit Gas Heating/Electric Cooling 3 to 15 Ton Small
Rooftop Units Accessory LP (Liquid Propane) Installation In-
structions for details.
Ensure each replacement orifice is tight as its threads into the
manifold pipe and the orifice projection does not exceed maxi-
Fig. 56 — Typical Gas Valves
IMPORTANT: Leak check all gas connections including
the main service connection, gas valve, gas spuds, and
manifold pipe plug. All leaks must be repaired before firing
unit.
Table 11 — LED Error Code Descriptions
*
LED INDICATION
ERROR CODE DESCRIPTION
ON
Normal Operation
OFF
Hardware Failure
1 Flash†
Evaporator Fan On/Off Delay Modified
2 Flashes
Limit Switch Fault
3 Flashes
Flame Sense Fault
4 Flashes
4 Consecutive Limit Switch Faults
5 Flashes
Ignition Lockout Fault
6 Flashes
Induced-Draft Motor Fault
7 Flashes
Rollout Switch Fault
8 Flashes
Internal Control Fault
9 Flashes
Software Lockout
LEGEND
LED —
Light Emitting Diode
* A 3-second pause exists between LED error code flashes. If more
than one error code exists, all applicable codes will be displayed in
numerical se
q
uence.
† Indicates a code that is not an error. The unit will continue to operate
when this code is displayed.
IMPORTANT: Refer to Tables 12 and 13 for additional trou-
bleshooting information.
PLASTIC ADJUST
SCREW
PLASTIC ADJUST
SCREW (2)
REGULATOR SPRING
(PROPANE - WHITE
NATURAL - SILVER)
REGULATOR SPRING (2)
(PROPANE - WHITE
NATURAL - SILVER)
GAS PRESSURE
REGULATOR
ADJUSTMENT
LOW STAGE
GAS PRESSURE
REGULATOR
ADJUSTMENT
MANIFOLD
PRESSURE TAP
MANIFOLD
PRESSURE TAP
NPT OUTLET
NPT OUTLET
INLET
PRESSURE TAP
INLET
PRESSURE TAP
ON/OFF
SWITCH
ON/OFF
SWITCH
REGULATOR
COVER SCREW
REGULATOR
COVER SCREW (2)
NPT INLET
NPT INLET
2 STAGE
SINGLE STAGE
Summary of Contents for 48GC04
