![background image](http://html1.mh-extra.com/html/carrier/42wm-09c-series/42wm-09c-series_installation-operation-and-maintenance-instructions_2560912084.webp)
0
Vdc
10
Vdc
CONTROLLER
Segnale / Signal / Signal
Signal / Señal / Signaal
Impedenza / Impedance / Impédance
Impedanz / Impedancia / Impedantie
< 100
Ω
1-10Vdc
< 1 Vdc
10 Vdc
Fan OFF con / Fan OFF with / Ventilateur OFF avec
Ventilator OFF mit / Ventilador OFF con / Fan OFF met
Velocità massima / Maximum speed / Vitesse maximale
Höchstgeschwindigkeit / Máxima velocidad / Maximale snelheid
43
Accessorio non incluso
Not included accessories
Accessoires non inclus
Zubehör nicht im Preis enthalten
Accessorios no incluidos
Accessoires niet inbegrepen
Il fuzionamento
della resistenza elettrica (Power-ON) deve avvenire
solo con ventilazione attiva (FAN-ON).
Alla disinserzione
della resistenza elettrica (Power-OFF) deve seguire
una post-ventilazione (FAN-ON) di 2 minuti.
The electric heater switching on (Power ON)
must occur only when the fan is working (FAN ON).
When the electric heater is switched off (Power OFF)
the fan must work (FAN ON) for at least 2 minutes.
Le fonctionnement
de la résistance électrique (Power-ON) doit
être seulement avec une ventilation active (FAN-ON).
La déconnexion
de la résistance électrique (Power Off) doit
suivre une post-ventilation (FAN-ON) 2 minutes.
Die elektrische Heizung lässt sich nur einschalten,
wenn der Ventilator geht.
Damit ist ein überhitzen nicht möglich.
Wenn die elektrische Heizung ausgeschalten wird,
läuft der Ventilator ca. 2min nach, damit keine
Überhitzung entsteht.
El funcionamiento
de la resistencia eléctrica (Power-On)
debe estar sólo con ventilación activa (FAN-ON).
La desconexión
de la resistencia eléctrica (Power OFF) debe seguir
un post-ventilación (FAN-ON) 2 minutos.
De werking van de elektrische weerstand
(Power-ON) mag alleen plaatsvinden wanneer
de ventilatie actief is (FAN-ON).
Op de uitschakeling van de elektrische weerstand
(Power-OFF) moet een postventilatie (FAN-ON)
van 2 minuten volgen.
Segnale
Comando Ventilatore
Fan Drive Signal
Signal
de Commande Ventilateur
Steuergerät Signal
Senãl
de Commando Ventilador
Fan Drive Signal
0 Vdc = Fan OFF / Fan OFF / Ventilateur OFF
Ventilator OFF / Ventilador OFF / Fan OFF
>1 Vdc = Fan ON / Fan ON / Ventilateur ON
Ventilator ON / Ventilador ON / Fan ON
10 Vdc = Velocità massima / Maximum speed
Vitesse maximale / Höchstgeschwindigkeit
Máxima velocidad / Maximale snelheid
COMANDI
E SCHEMI ELETTRICI
ELECTRICAL
CONTROLS AND
WIRING DIAGRAMS
MFC
= Morsettiera
del FAN COIL
M
= Motoventilatore
E
= Valvola acqua
BLAC
= Scheda elettronica
Inverter
Tp
= Collegamento
protezione termica
motore
0-10 Vdc
= Segnale ingresso
U/V/W
= Collegamento
motore
A+/A-
= Segnali digitali
P+/P-
= Segnali digitali
CONTROLLER
= Regolatore
MP
= Pompa
di evacuazione
condensa
R1
= Resistenza elettrica
B2
= Termostato
di sicurezza
a riarmo automatico
B3
= Termostato
di sicurezza
a riarmo manuale
Q1
= Relè di attivazione
resistenza elettrica
GNYE
= Giallo/Verde
WH
= Bianco
RD
= Rosso
BK
= Nero
BU
= Blu
EH
= Ingresso per
resistenza elettrica
MFC
= Fan coil
terminal board
M
= Fan
E
= Water valve
BLAC
= Inverter circuit
board
Tp
= Motor fan thermal
protector
connection
0-10 Vdc
= Input signal
U/V/W
= Motor fan
connection
A+/A-
= Digital fault signals
P+/P-
= Digital fault signals
CONTROLLER
= Controller
MP
= Condensate pump
R1
= Electrical heater
B2
= Self reset
safety thermostat
B3
= Manual reset
safety thermostat
Q1
= Electrical heater
Power-ON relay
GNYE
= Yellow/Green
WH
= White
RD
= Red
BK
= Black
BU
= Dark Blue
EH
= Input for electrical
heater
LEGENDA
LEGEND
• Impianto senza valvole
• Termostatazione sul
motore
• Without valves
installation
• Thermostatic control
on the fan
• Impianto 2 tubi
(1 valvola)
• Termostatazione sulla
valvola
• 2-tube installation
(1 valve)
• Thermostatic control
on the valve
• Impianto 2 tubi
(1 valvola)
• Termostatazione sulla
valvola
• Pompa di evacuazione
condensa
• 2-tube installation
(1 valve)
• Thermostatic control
on the valve
• Condensate pump
A
B
C
A
B
C