background image

1. Run the drain hose sloping downward. Do
    not  install  the  drain  hose  as   illustrated
    below.

2. When  connection  extension  drain  hose,
    insulate the  connecting part of  extension
    drain hose with a shield pipe

Do not form a rise

Connective
pipe

Pipe holder

Pipe cover

Right piping

Left piping

Pipe cover

Drain hose

Connective
pipe

Pipe room

Ponding box

Indoor unit outline

Connective pipe

Right back piping

Left back piping

Wrapping belt

Do not put the hose
end into water

Indoor unit

1. For  the  left-hand  and  right-hand  piping,
    remove the rear plate bushing from the left
    side of the rear plate.
    Explain to clients that the pipe cover must
    be kept as it may be used when relocate
    the air conditioner to any other place.
2. For the left-hand and rear-left-hand piping,
    install the piping as shown. Bend the conn-
    ective  pipe to  be  laid at  43mm  height or
    less from the wall.

3. Fix the end of the connective pipe.
    (Refer to Tightening Connection in REFRI-
    GRANT PIPING CONNECTION)

Connect the indoor unit first then the outdoor
unit and bend and arrange the pipe carefully.
Do not  allow the  piping  to let  out from the
back of the indoor unit.
Be careful not to let the drain hose slack.
Insulate both of the auxiliary piping.
Banding the drain hose under the auxiliary
pipe.
Do not  allow the  piping to  let out  from the
back of the indoor unit.

Wind the connective cable, drain hose and
wiring with tape securely, evenly as shown
below.
   Because the condensed water from rare
   of the indoor unit is gathered in ponding
   box and is piped out of room. Do not put
   anything else in the box.

.

.

.

.

..

.

.

.

.

.

.

.

.

.

. .

.

.

.

.

.

.

.

.

. .

.

.

. .

.

.

. .

.

.

.

.

.

.

. .

.

. .

.

.

.

.

.

.

.

.

. .

.

.

. .

.

.

.

.

.

. .

.

. . .

.

.

.

.

.

.

. .

.

.

.

.

.

.

. .

.

.

.. .

.

.

.

.

. .

.

.

.

.

.

. .

.

.

.

.

..

.

.

. .

.

.

. .

.

.

.

.

.

. .

.

.

.

.

.

. .

.

.

.

.

.

.

.

.

.

.

. .

.

.

.

.

.

.

.

.

......

..

.

.

.

...

4

3

3. Piping and bandaging

1. Drainage

2. Connective pipe

CAUTION

2. Connective Pipe and Drainage Installation

.

..

.

. .

..

.

.

.

.

.

.

.

.

.

.

.. .

..

.

.

.

.

.

.

.

.

.

.

42HQE009(012)/38YE009(012)

GB

ENGLISH

GB-5

Summary of Contents for 38YE009(012)














Reviews: