background image

6

Centre of gravity coordinates

Placement on site

Once the unit is discharged, it must be freed from the transport 
supports so that the inserts available for the silent-blocks can be 
accessed. 
Each support is 

fi

 xed to the crossbar using 2 M4 screws. 

M4 screws for 

fi

 xing the support 

Mounting 

hole

Location designation

Before moving the unit, it must be checked that all panels are 
fastened in place. Lift and lower with care.
When choosing the location, whatever may be the selected fashion, 
the following precautions have to be taken into consideration:

 

It is mandatory to comply with norm EN 378-3 on Safety and 
Environmental Requirements. Part 3: “In situ” installation and 
protection to people.

 

The area where the unit will be located must be perfectly accessible 
for cleaning and maintenance operations (check minimum free 
space for maintenance). Leave enough space for air circulation 
around the unit.

 

Check that the unit is perfectly levelled.

 

It is necessary to check that the surface of the 

fl

 oor or the 

structure supports the weight of the unit (please, consult the 
weight of the unit in the section “Anchorage for silent-blocks”). 

 

Foresee appropriate damping devices in all the installation so 
that noise and vibration transmission is avoided (refer to the 
“Anchorage for silent-blocks”). 
In the event of assembling directly on silent-blocks to the 
ground, it is recommended that a template of the unit’s footprint 
with the anchoring points of the silent-blocks be made.
With the help of the crane or the forklift truck, the unit will be 
raised to a su

  cient height that the silent-blocks can be screwed 

into its base. The 4 silent-blocks must remain oblique and the 
interiors perpendicular to the unit. 
M10 metric threads have been provided for their placement in 
the supports indicated in the following section “Anchorage for 
silent-blocks”. A hex key 17 or Allen wrench 8 will be used for 
this operation based on the 
type of screw used.
This image shows how the 
silent-block option that can be 
supplied for this unit is 

fi

 xed 

to the unit.

7 - LOCATION AND ASSEMBLING

Minimum free space for commissioning and

maintenance operations

1m

1m

0,5m

A

30PA

A (m)

90STD to 100STD

1,2

120STD to 180STD

1,5

30PA

A (m)

90HEE

1,2

100HEE to 120HEE

1,5

160HEE to 180HEE

1,2

30PA

Centre of gravity 

(mm)

Weight

empty 

(kg)

X

Y

Z

90STD

453 384 528

302

100STD

488 398 576

310

120STD

625 399 676

372

160STD

619 400 666

390

180STD

625 397 674

388

90HEE

502 422 614

294

100HEE

569 417 673

351

120HEE

628 426 742

368

160HEE

940 435 573

450

180HEE

936 434 579

455

Since it is an unit designed to work indoors, some specific 
installation norms must be followed:

 

Ensure that the location of the supply and return grilles does 
not generate air recirculation.

 

Check that there are no obstructions in the air supply and return 
grille slats due to being tightly closed

6 - TRANSPORT AND HANDLING

Summary of Contents for 30PA 180





























Reviews: