manualshive.com logo in svg

Carrier Access Wide Bank 28 DS3, Overview, Page: 40 / 50

Share
Download
Carrier Access Wide Bank 28 DS3 Overview Download Page 40

38

Wide Bank 28 DS3 - Release 2.4

PM Reports

PM Reports

The following steps show how to configure and retrieve performance monitoring reports.

1. Allow or Inhibit PM Reports

ALW-PMREPT-T3:tid:aid:ctag;

ALW-PMREPT-T1:tid:aid:ctag;

ALW-PMREPT-E1:tid:aid:ctag;

ALW-PMREPT-ALL:tid:ALL:ctag;

INH-PMREPT-T3:tid:aid:ctag;

INH-PMREPT-T1:tid:aid:ctag;

INH-PMREPT-E1:tid:aid:ctag;

INH-PMREPT-ALL:tid:ALL:ctag;

2. Retrieve PM Reports

RTRV-PM-E1:tid:aid:ctag::[montype],[monlev],[locn],,[tmper],[mondat],[montm];
RTRV-PM-T1:tid:aid:ctag::[montype],[monlev],[locn],,[tmper],[mondat],[montm];
RTRV-PM-T3:tid:aid:ctag::[montype],[monlev],[locn],,[tmper],[mondat],[montm];

Example:

Retrieve PM report for DS1 #5 at 15-minute intervals.

RTRV-PM-T1:tid:DS1-05:::,,,,15-MIN,,;

3. Retrieve PM Schedule

RTRV-PMSCHED-T3:tid:aid:ctag;

RTRV-PMSCHED-T1:tid:aid:ctag;

RTRV-PMSCHED-E1:tid:aid:ctag;

RTRV-PMSCHED-ALL:tid:aid:ctag;

4. Schedule PM Reports

SCHED-PMREPT-T3:tid:ALL:ctag::[repinvl],[reptstatm],[numrept],,[monlev],

[locn],,[mper],[tmofst];

SCHED-PMREPT-T1:tid:ALL:ctag::[repinvl],[reptstatm],[numrept],,[monlev],

[locn],,[mper],[tmofst];

SCHED-PMREPT-E1:tid:ALL:ctag::[repinvl],[reptstatm],[numrept],,[monlev],

[locn],,[mper],[tmofst];

Example:

Schedule ten T1 Performance Reports at 15-minute intervals.

SCHED-PMREPT-T1:tid:ALL:::15-MIN,,10,,,,,15-MIN;

Facility

AID

T3

DS3-A, DS3-B, or 

ALL

T1

DS1-1 to DS1-28, or 

ALL

E1

E1-01 to E1-27, or 

ALL

 

(see 

T3-E1 Configuration 

AIDs

 on 

page 8

)

ALL

ALL

Summary of Contents for Wide Bank 28 DS3



















































Reviews:

No comments