manualshive.com logo in svg

Carefree Freedom RM, Service Manual, Page: 9 / 27

Share
Download
Carefree Freedom RM Service Manual Download Page 9

Carefree of Colorado

 Service 

Manual 

F

REEDOM 

RM 

052978-351r8 

6 

C

ANOPY 

R

EPLACEMENT 

(C

URRENT 

C

ONFIGURATION

) 

This procedure requires two people. 
1.  Open the awning 18"-24". 
2.  Disconnect power to the awning. 
3.  Carefully push the lead rail toward the case so that the arms collapse and 

the fabric is slack. 

4.  Hold the lead rail in this position and firmly tie the elbows of the spring arms 

together.  Use a minimum 1/2" rope - do not use bungee cords.  When tying 
the rope, use a non-slip knot such as a square knot or equivalent. 

  

CAUTION

   

Failure to secure the lead rail as described will allow the spring arms to 

unexpectedly extend out possibly causing personal injury and damage to the awning. 

1.  On the RH (idler) side: 

1.1. Remove the lead rail end plate and set aside. 
1.2. Remove the outer end cap and set aside. 
1.3. Remove the two (2) cover screws from the end plate. 

2.  On the LH (motor) side: 

2.1. Remove the fabric retaining screw from the lead rail endplate. 
2.2. Remove the outer end cap and set aside. 
2.3. Remove the five (5) plate screws and two (2) motor screws.  Set 

parts aside. 

2.4.  Slide the end plate along the motor cable so that it is out of the way. 
2.5. Remove the fabric retaining screw from the motor crown. 

3.  Rotate the top cover back and out of the way. 

4.  Partially pull the roller tube away from the idler plate until the idler 

plug is clear. 

5.  Carefully lift the roller tube up. 

 

6.  Do the following 2 steps at the same time. 

6.1.  Pull the roller tube out the idler end of the case while pulling the fabric from the lead rail. 
6.2.  Have a second person pull the motor assembly from the roller tube. 

7.  Note the orientation of the old canopy then unwrap and remove from the roller tube. 
8.  Unfold the replacement fabric then slide the new fabric onto the roller tube and center. 

NOTICE

  

While the awning fabric is fairly robust, care must be taken not to snag the fabric when 

sliding into the roller tube or lead rail. 

Tip:  Lightly spraying the slots with a dry silicone lubricant will help the fabric slide into the slots without 
staining the material. 

9.  Roll the fabric onto the roller tube leaving enough material to reach between the case and the lead rail. 
10. Begin sliding the fabric into the lead rail and the roller tube into the case. 

Retaining

Screw

Fabric Slot

RMF047

Motor Side

Idler Side

Retaining
Screw

Fabric Slot

Motor

FRM007

Spring Arms

Firmly Tie Elbows Together

RMF047a

Cover

End Cap

Motor Screws

(x2)

End Plate

Plate Screws (x5)

Leadrail

Endplate

End Plate

End Cap

Cover
Screws (x2)

Summary of Contents for Freedom RM




























Reviews:

No comments