Carefree Freedom RM Service Manual Download Page 14 | Manualshive

Page: 14 / 27

Carefree Freedom RM Service Manual Download Page 14

Carefree of Colorado

Service

Manual

F

REEDOM

RM

052978-351r8

11

R

EPLACING THE

M

OTOR

(O

RIGINAL

C

ONFIGURATION

)

1. From the motor end cap remove the cover, end cap and motor screws.

2. Remove the end cap.

3. Disconnect the motor wires from inside the vehicle and pull out

or

clip the motor wires. If cutting the

wires, cut them close to the motor to leave enough wire that can be stripped and spliced.

4. Pull the motor out of the roller tube and set aside.
5. Attach the one-way drive to the new motor with the "A" pointing toward the motor. Secure with the supplied

clip.

NOTICE

The one-way drive must be oriented with the "A" facing the motor. If the drive is not

oriented correctly, the awning will not to operate and the arms will spring out when released.

6. Align the one-way drive with the roller tube and start sliding the new motor into the roller tube.
7. Attach the end cap to the motor with the motor screws removed previously. Ensure that the motor is oriented

with the limit switches pointed toward the access holes in the cap.

8. Route the new motor wire into the vehicle and attach or if the wires were cut, splice the new wires to the

existing wires. Match the wires ( Blue to Blue and Brown to Brown. Push the splices into the vehicle
then use a quality silicone sealant to seal the wire hole into the vehicle.

NOTE:

If splicing the wires, allow enough lead wire from the motor so that the completed splices can be

pushed into the wall before sealing. There is not clearance room in the case for the wires and splices.

9. Align the bearing on the motor and slide into the roller tube.

10. Align the screw holes in the end cap and attach to the awning case.

11. While holding the lead rail, carefully remove any roller tube supports and arm ties. Allow the lead rail to

extend until the fabric is taunt. If the lead rail continues to extend after the fabric is taut, the one way
drive was installed backwards. Retie the arms, remove the motor and orient the one way drive as
shown above.

12. To test, restore power then extend and retract the awning.

13. After replacing the motor, it will be necessary to adjust the motor limits (page 2).

RMF024

Motor Screws

Cover

Screw

Cover Screw

End Cap
Screws

End Cap

Bearing

Motor

“A”

One-Way Drive

Clip

«
...
12
13
14
15
16
...
»

Summary of Contents for Freedom RM




























Reviews:

No comments