manualshive.com logo in svg

Carefree Freedom RM, Service Manual, Page: 26 / 27

Share
Download
Carefree Freedom RM Service Manual Download Page 26

Carefree of Colorado

 Service 

Manual 

F

REEDOM 

RM 

052978-351r8 

23 

F

REEDOM 

RM

 

B

RACKET 

K

ITS

 

Bracket kits are ordered separately.  Several types are available based on the application installation.  
Bracket mounting instructions are separate supplements of the installation manual. 

Bracket kits are ordered separately.  Several types are available based on the application installation.  
Bracket mounting instructions are separate instructions that supplement this manual. 

BS0001 Flat 

Roof 

 

4m and less 
Mill Finish 
Awning Hardware included 
Bracket Mounting Hardware Installer Furnished 
 
Instruction Supplement:  052570-001 

BS0002 Sprinter 

 

4m and less 
Mill Finish 
 
Bracket and Awning Hardware included 
 
Instruction Supplement:  052570-002 

BS0003 Hymer 

SX 

 

(-2) 2 Brackets 3m and less 
(-3) 3 Brackets 3.5m & 4m 
(-4) 4 Brackets 4.5m & 5m 
Mill Finish 
Bracket and Awning Hardware included 
Instruction Supplement:  052570-003 

BS0009 

Dodge ProMaster; Fiat Ducato 

 

4m and less 
Mill Finish 
 
Bracket and Awning Hardware included 
 
Instruction Supplement:  052570-009 

 

 

 

16"

BS0001a

(x2)

(x2)

(x2)

36"

BS0002a

16"

BS0003a

-2 (x2)
-3 (x3)
-4 (x4)

BS0009a

(x3)

Summary of Contents for Freedom RM




























Reviews:

No comments