manualshive.com logo in svg

Carefree Freedom RM, Service Manual, Page: 4 / 27

Share
Download
Carefree Freedom RM Service Manual Download Page 4

Carefree of Colorado

 Service 

Manual 

F

REEDOM 

RM 

052978-351r8 

1 

P

RODUCT 

S

PECIFICATIONS

 

 

Widths:

 

 

Available Sizes for Motorized Freedom RM 

 

 

Available Sizes for Manual Freedom RM 

  

 

centimeters 

244 257 300 350 400 450 500 

inches 

96  101 118 138 157 177 197 

Extension:

 

180cm (72")  200cm (80")

250cm (98") 

NOTE:  Actual awning Length:  Motorized = 2.69" shorter than stated length; 

Manual = 2" shorter than stated length 

Note:  4.5 meter and 5 meter awnings are only available in the motorized configuration. 

L

EADING 

E

DGE 

P

OSITION 

A

CTUATION AND 

C

ONTROL

 

Power: 

Lateral Arm Spring 

Minimum Tension:

 

Open 

Position Control:

 

Motorized: 

Roll Out/In Controlled by Electrical Motor  

SPDT, Center Off Switch 

 

Manual: 

Roll Out/In Controlled by Manual Crank 

M

OTOR 

S

PECIFICATIONS

 

Motor Type: 

Tubular 

Power: 

12VDC 

Minimum:

 10VDC 

Output:

 30 Watts

 

 

Nominal Current:

 2.5Amps 

Max Current:

 14Amps (stall @ min voltage) 

Power Source: 

Motor and controls are routed and hardwired into the vehicle’s 12V system 

Speed 

15 rpm 

C

OLORS 

A

VAILABLE

 

Case 

Satin, White or Black 

Fabric:

1

 

Vinyl 

 

RMF001e

Awning Length

Fabric Width

3.8cm

[1.5"]

5cm 

[2"]

15.4cm

[6"]

16.5cm

[6.5"]

Motorized

Current Configuration (up to 5 meter)

Awning Length

Fabric Width

3.8cm

[1.5"]

5cm 

[2"]

15.4cm

[6"]

16.5cm

[6.5"]

Motorized

Original Configuration (up to 4 meter)

Awning Length

Fabric Width

5cm 

[2"]

9.4cm 

[3.7"]

15.4cm

[6"]

16.5cm

[6.5"]

Motorized

Original Configuration (4.5 & 5 meter)

Awning Length

Fabric Width

3.8cm

[1.5"]

6.9cm 

[2.7"]

15.4cm

[6"]

16.5cm

[6.5"]

Manual Crank

Current

Original

There are two configurations of the motorized Freedom RM.
The original configuration is identified by the five (5) screws in the endcap.
The current configuration has one (1) screw in the endcap.

Dimensions shown are given for reference only and may vary based actual installation.

Summary of Contents for Freedom RM




























Reviews:

No comments