background image

12

      Part Number 3E1086 R2

September 2002

Set DIPSW1:7 to ON.

Present a Prox 125 card to the Prox Plus 125 reader.

Note:You must present the card within 30 seconds of setting DIPSW1:7 to ON. If

you are initialising with two readers connected to the URI, you should present
the card to the reader on URI plug P5.

Set DIPSW1:7 to OFF

The green LED (D44) will begin flashing continuously.

The other red LED (D10) will flash each time the URI replies to a poll from the
Commander.

Replace the lithium battery jumper (J1).

Restore the tamper by closing the door of the cabinet.

Approvals and Standards

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.

If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

Note:

Changes or modifications not expressly approved by Cardax (International)
Ltd could void the user's authority to operate the equipment.

Summary of Contents for Prox Plus 125














Reviews: