Car-Interface r.LiNK CI-RL5-MIB2-E Manual Download Page 17 | Manualshive

Page: 17 / 24

background image

Version 08.05.2019

MIB-Entry-5inch (180514)

CI-RL5-MIB2-E

P

a

g

e

17

2.4.4.

Fixing – daughter PCB

Note:

For Skoda head unit installation, the 6pin interface cable and the 4pin pushbutton

cable connections have to be done

before

fixing the PCP to the head unit!

Change the original brass screw against one of the enclosed brass spacers at the
position that’s shown in the picture.

Fix the daughter PCB to the previously fixed brass spacer in the head unit by using the
original screw.

«
...
15
16
17
18
19
...
»

Summary of Contents for r.LiNK CI-RL5-MIB2-E

























Reviews:

No comments

Related manuals for r.LiNK CI-RL5-MIB2-E

Spacemaker 7-5400

Brand: GE Pages: 12

Brand: Magnavox Pages: 26

Brand: Bang & Olufsen Pages: 20

Brand: Bang & Olufsen Pages: 24

BeoSound Ouverture

Brand: Bang & Olufsen Pages: 44

Brand: Pyle Pages: 24

Brand: Wayne Pages: 1

Brand: Directed Video Pages: 27

Brand: aija audio Pages: 4

Brand: Tokai Pages: 42

Brand: Boss Audio Systems Pages: 16

Audio 30 Export 3301

Brand: Becker Pages: 92

Brand: Trevi Pages: 46

MEISTERSTUCK SO-610

Brand: Sonoro Pages: 334

Wireless music system for iPod

Brand: Brookstone Pages: 14

Brand: Clarion Pages: 66

Brand: Pioneer Pages: 8

Brand: Pioneer Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands