24 Instruction manual C775G, C750G, C768G
Please keep this instruction manual for future reference
I N S TA L L I N G T H E A P P L I A N C E
1. Remove the pan supports, the burner lid and flame spreader and carefully turn the appliance
upside down and place it on a cushioned mat. Take care that the Ignition devices and flame
supervision devices are not damaged in this operation.
2. Apply the sponge provided around the edge of the appliance.
3. Do not leave a gap in the sealing agent or overlap the thickness.
Do not use a silicon sealant to seal the
appliance against the aperture.
This will make it difficult to remove the
appliance from the aperture in future,
particularly if it needs to be serviced.
Neglect of this mark may result in severe personal injury or death.
Danger/Warning
Neglect of this mark may result in minor personal injury or
property damage.
No naked flames
No Access
Must Do
DANGER
If gas appears to be leaking, take the following actions:
-
Do not turn on the light.
-
Do not switch any electrical appliance on or off and do not touch any electric plug.
-
Do not use a telephone.
1 Stop using the product and close the middle valve.
2 Open the window to ventilate.
3 Contact our service centre or gas supplier by using a phone outside.
* The gas contains mercaptan, so that you can smell the gas leak (smell of rotten garlic or egg) even where only
1/1000 of the gas is in the air.
WARNING SYMBOLS
Caution
(A) SEALING STRIP
(C) SCREW
(B) BRACKET
1. Remove the pan supports, the burner lid and flame spreader and carefully turn the appliance upside
down and place it on a cushioned mat. Take care that the Ignition devices and flame supervision devices
are not damaged in this operation.
2. Apply the sponge provided around the edge of the appliance.
3. Do not leave a gap in the sealing agent or overlap the thickness.
1. Place the bracket (B) over the holes that match the size of the
screws.There are one set of screw holes in each corner of the hob (H).
Slightly tighten a screw (C) through the bracket (B) so that the
bracket is attached to the hob, but so that you can still adjust
the position.
2. Carefully turn the hob back over and then gently lower it into the
aperture hole that you have cut out.
3. On the underneath of the hob, adjust the brackets into a position that
is suitable for your worktop.
Then fully tighten the screws (C) to secure the hob into position.
Do not use a silicon sealant to seal the appliance against
the aperture.
This will make it difficult to remove the appliance from
the aperture in future, particulary if it needs to
be serviced.
I N S T A L L I N G T H E A P P L I A N C E
1. Place the bracket (B) over the holes that
match the size of the screws.There are
one set of screw holes in each corner of
the hob (H). Slightly tighten a screw (C)
through the bracket (B) so that the bracket
is attached to the hob, but so that you can
still adjust the position.
2. Carefully turn the hob back over and then
gently lower it into the aperture hole that
you have cut out.
3. On the underneath of the hob, adjust the
brackets into a position that is suitable for
your worktop.
4. Then fully tighten the screws (C) to secure
the hob into position.
(A) SEALING STRIP
(C) SCREW
(B) BRACKET
1. Remove the pan supports, the burner lid and flame spreader and carefully turn the appliance upside
down and place it on a cushioned mat. Take care that the Ignition devices and flame supervision devices
are not damaged in this operation.
2. Apply the sponge provided around the edge of the appliance.
3. Do not leave a gap in the sealing agent or overlap the thickness.
1. Place the bracket (B) over the holes that match the size of the
screws.There are one set of screw holes in each corner of the hob (H).
Slightly tighten a screw (C) through the bracket (B) so that the
bracket is attached to the hob, but so that you can still adjust
the position.
2. Carefully turn the hob back over and then gently lower it into the
aperture hole that you have cut out.
3. On the underneath of the hob, adjust the brackets into a position that
is suitable for your worktop.
Then fully tighten the screws (C) to secure the hob into position.
Do not use a silicon sealant to seal the appliance against
the aperture.
This will make it difficult to remove the appliance from
the aperture in future, particulary if it needs to
be serviced.
I N S T A L L I N G T H E A P P L I A N C E