background image

 

WSD15IIDIST 

User Manual

 

 

 

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57 
10090 CASTIGLIONE TORINESE - TORINO - ITALY 
VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210 
e-mail

 

[email protected]

 - web 

www.capetti.it

 

 

WA0416E_WSD15IIDIST_User Manual_R05 

V5.0

 

 

10.

 

Stand-alone USB datalogger installation. 

Install the 

datalogger

 in appropriate place. 

If the sampling process has not yet been activated, you can start it through th

WineCapKey

 

Bring it closer to the sensitive point, wait for 2 flashes (

TEST

) (

refer t

Picture 3 - Commands table

and remove. The 

datalogger

 begins 

sampling according to your settings through your PC. 

Through th

WineCapKey

 is possible to ask for the status, bring it close to the 

datalogger

 for 1 flash (

STATE

) and remove it. 

STAND-ALONE MODE STATUS 

Table:  

Flash count - Stand-alone mode 

STATUS 

 

1 green flash 2 seconds long 

ACTIVE 

 

2 red flashes 2 seconds long 

STANDBY 

 

Sequence  of  red  flashes:  short,  2 
seconds long, short 

FACTORY RESET  

INVALID

 

datalogger

 clock! 

PC connection required 

 

11.

 

Shutting off/Reactivating the device. 

If the device is shut off and left unused for a long time, you can issue the 

STANDBY

 command (

refer t

Picture 3 - Commands table

). It 

corresponds to the command number 4 and must be issued twice to confirm the operation.  

Position the 

WineCapKey

 in the spot indicated i

Picture 2 - WineCapKey positioning

 and wait for four 

AMBER

 flashes, then remove 

th

WineCapKey

 from device.  

Verify  that  the  device  asks  for  confirmation  of 

STANDBY

  command  with  alternate 

GREEN/RED

  flashing,  then  position  again  the 

WineCapKey

 and wait for four flashes again. The device will confirm the 

STANDBY

 status lighting the 

RED

 led for 2 seconds twice. 

To reactivate the device the 

TEST

 command must be issued.

 

 

 

Picture 5 - Stand-alone datalogger status

 

Summary of Contents for WineCap WSD15IIDIST











Reviews: