CanyCom S160 Operator'S Manual Download Page 64

Page: 64 / 75

-55-

Maintenance

3. Visually inspect that battery fluid level is

between the "Upper Level" and "Lower
Level" lines. If the fluid level is below the
"Lower Level," fill.

UPPER LEVEL

LOWER LEVEL

Filler Plugs

3570M-0509-020E

1. Park the machine on level ground.
2. Unlatch battery cover latch and open battery

cover.

Inspecting

3683M-0508-010E

Battery Cover

Battery Cover Latch

• Always remove battery from the machine before charging. Failure to do so may

cause damage to the electrical components and wiring.

• Follow the battery charger user's manual when charging.

Filling

UPP

ER L

EVE

LOWER LEVEL

3683M-0508-020E

Battery

Battery Bracket

Upper Level

Lower Level

4. Remove battery bracket and battery from

the machine.

5. Open filler plugs and add distilled water to

battery evenly until fluid level is between the
"Upper Level" and "Lower Level" lines.

6.  Put filler plugs back in place.
7.  Install battery.
8.  Close battery cover and latch it.

Summary of Contents for S160












































































Search results

Summary of Contents for S160

Reviews:

Related manuals for S160

Brands by name

Popular brands

CanyCom S160, Operator'S Manual

Search results

Summary of Contents for S160

Reviews:

Related manuals for S160

Brands by name

Popular brands