CanyCom S160 Operator'S Manual Download Page 54

Page: 54 / 75

-45-

Maintenance

1.  Open engine cover.
2.  Have an appropriate drain pan.
3.  Remove coolant drain plug to drain coolant.

Wash inside radiator.

4. Put drain plug back in place and tighten it

securely.

5. Fill coolant.
6. Close engine cover.

3683M-0506-070E

Coolant Drain Plug

Changing

Fuel Filter

1.  Open engine cover.
2.  Turn fuel cock to [Off] position.
3.  Follow the instructions in the

Operator's

Manual for the engine

to inspect, clean, or

change fuel filter.

4. Turn fuel cock to [On] position.
5. Close engine cover.

• Fuel is highly flammable. Keep fire and spark away when servicing fuel filter. If

fuel is spilt, wipe immediately.

3683M-0506-080E

Fuel Filter

Off

Fuel Cock

Inspecting/Cleaning

• Coolant Capacity (excluding reservoir): 3.5L
• Reservoir Capacity: 0.7L
•Removing radiator cap helps drain the

coolant.

NOTE

• Dispose risidual fuel in fuel filter properly.

Summary of Contents for S160












































































Search results

Summary of Contents for S160

Reviews:

Related manuals for S160

Brands by name

Popular brands

CanyCom S160, Operator'S Manual

Search results

Summary of Contents for S160

Reviews:

Related manuals for S160

Brands by name

Popular brands