manualshive.com logo in svg

Cantium Scientific MicroBio MB2, Operating Manual

Share
Download
Cantium Scientific MicroBio MB2 Operating Manual Download Page 32

Change Plate / Dish Type

The  MicroBio  MB2  can  accommodate  both  55mm/65mm  contact  plates  or 

90mm  petri  dishes.  The  MicroBio  MB2  is  factory  fitted  with  the  petri  dish 
springs (Cantium Scientific Limited part number A-00070), but these can be 
removed  and  replaced  with  the  supplied  contact  plate  springs  (Cantium 
Scientific Limited part number A-00068).  

The  springs  for  both  types  have 
slots to allow a degree of adjustment 
to  suit  dish/plate  manufacturer 

variations.

To  change  the  spring  type  remove 
the  three  screws  as  highlighted 
using  the  2mm  hex-key  supplied 
with the kit. Lift off the support plate 
and  springs,  then  refit  using  the 

same screws, support plate and the 
required  springs.  Care  must  be 
taken  not  to  over-tighten  or  cross-
thread any of the screws.  

Replacement  screws  are  available  from  Cantium  Scientific  Limited,  part 
number A-00232 or contact your local distributor.

31

Summary of Contents for MicroBio MB2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands