manualshive.com logo in svg

Cantium Scientific MicroBio MB2, Operating Manual

Share
Download
Cantium Scientific MicroBio MB2 Operating Manual Download Page 15

Inserting a Contact Plate or Petri Dish

Carefully  remove  the  sampling  head  cover  from 
the  MicroBio  MB2,  unless  it  is  being  carried 
separately  in  a  sterile  container.    Only  hold  the 
edge of the head.  

Do not touch the perforated 

or inside surfaces.

    

With  the  sampling  head  removed,  insert  a  petri 
dish/contact  plate  inside  the  springs,  so  that  its 
base  sits  firmly  on  the  support  plate,  then  re-fit 
the sampling head.

The  standard  MicroBio  MB2  can  use  220  or  400 

hole sampling heads. The 220 hole sampling head 
can be used with both 55mm/65mm contact plates 
or 90mm petri dishes, but only the centre 55mm of 
the petri dish will collect samples. Using the 400 x 
0.7mm  hole  sampling  head  will  give  nearly  full 

coverage of a 90mm petri dish, improving reliability 
of counts.

The  MicroBio  MB2-HiFlow  model  can  only  use 
90mm  Petri  dishes  and  the  400  x  1mm  hole 
sampling head. 

ALWAYS STERILISE THE SAMPLING HEAD 




PRIOR TO EACH USE




14

Summary of Contents for MicroBio MB2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands