Canon Remote FAX Kit-A1 Service Manual Download Page 37

Page: 37 / 42

4-9

Maintenance > Trobleshooting > Communication Error > Receiving Failure

Error

Codes

Cause

Remedy

#037

The document could not be sent because

there was insufficient memory available.

Delete unnecessary documents and documents

with errors to make more memory available.

Data that contains more than 1,000 pages

is received.

This machine can print or store up to 999 pages

of data in memory, but will delete any data that

exceeds this limit. Ask the sender to resend the

remaining pages.

Delayed sending or redial failed because

the image data is not stored in memory.

Try scanning the document again, and then

resend.

Press [Direct Send] when trying again.

When sending fax to the multiple

destinations, the document cannot be sent

because there was insufficient memory

available.

Delete unnecessary documents and documents

with errors to make more memory available.

Divide the document into two or more parts.

Resend the document at a lower resolution.

#040

When sending fax from the Remote Fax

client machine, the document cannot

be sent because there was insufficient

memory available in the Remote Fax

Server.

Delete unnecessary documents and documents

with errors to make more memory available.

Divide the document into two or more parts.

Resend the document at a lower resolution.

#080

A subaddress is not set in the recipient's

machine.

Try sending the document without a

subaddress, or request that the recipient set the

same subaddress as the sender's subaddress.

#081

A password is not set in the recipient's

machine.

Try sending the document without a password,

or request that the recipient set the same

password as the sender's password.

#102

The subaddress and/or password do not

match.

Check the subaddress and/or password of

the recipient's machine, make sure that the

subaddress and password you are sending with

the document matches the recipient's, and then

try again.

Error

Codes

Cause

Remedy

#107

The document could not be sent because

there was insufficient memory available.

Resend the document at a lower resolution.

Delete unnecessary documents in the Mail Box

and the Fax/I-Fax Inbox to make more memory

available.

If this problem occurs frequently, contact your

local authorized Canon dealer.

#701

The specified Department ID does not

exist, or the password has changed.

Enter the correct Department ID or password

using - (numeric keys) on the control panel,

and then try sending again.

The Department ID or password was

changed during the job.

Try performing the job again with the new

Department ID and password. If you do not

know the password, contact your System

Manager.

<Allow Printer Jobs with Unknown

IDs> in Department ID Management

in Management Settings (Settings/

Registration) is set to 'Off'.

Set <Allow Printer Jobs with Unknown IDs> in

Department ID Management in Management

Settings (Settings/Registration) to 'On'.

The document cannot be sent because

the authentication failed between the

Remote Fax client machine and Remote

Fax Server.

If the Department ID is set in the Remote

Fax Server, log in to the Remote Fax client

machine with the Department ID and password

registered in the Remote Fax Server.

#702

The document could not be sent because

the memory is full.

Wait a few moments, and then try again after

the other send jobs are complete.

Do not send the document to too many

recipients at the same time. Send the document

to a smaller number of recipients.

#703

The memory for the image data is full.

Wait a few moments, and then try again after

the other send jobs are complete.

Delete documents stored in the Mail Box and

Fax/I-Fax Inbox. If the machine still does not

operate normally, turn the main power OFF, and

then back ON.

#704

An error occurred while reading address

information from the Address Book.

Check the address settings. If the machine still

does not operate normally, turn the main power

OFF, and then back ON.

Summary of Contents for Remote FAX Kit-A1











































Search results

Summary of Contents for Remote FAX Kit-A1

Reviews:

Related manuals for Remote FAX Kit-A1

Brands by name

Popular brands

Canon Remote FAX Kit-A1, Service Manual

Search results

Summary of Contents for Remote FAX Kit-A1

Reviews:

Related manuals for Remote FAX Kit-A1

Brands by name

Popular brands