manualshive.com logo in svg

Canon LBP-1000, Service Manual

Share
Download
Canon LBP-1000 Service Manual Download Page 77

B. Operation Panel
1. Outline

The operation panel has one LCD with 16 characters by 2 lines, six switches, and three LEDs.

The operation panel is connected with the video controller PCB and has the following func-

tions.
a. Displays status and error message on the LCD.
b. Displays condition of the operation on the LED.
c.

Changes menu to activate and the set values with the switches.

2. Operation

The LCD and LEDs on the operation panel are controlled by the signal output from the video
controller.  Any signals indicated by the switches on the operation panel are input to the video
controller.

Figure 2-6-3

CHAPTER 2

2 - 43

LEDs

nSCEN

nPNLCLK

nCOMWR

nDENB

PNLWR

PNLRD

J1-9

-8

-7

-6

-5

-4

-3

-2

-1

J1-1

-2

-3

-4

-5

-6

-7

-8

-9

AIR

Gate Array

LEDs

Switches

LCD

LCD

contoller

J2-A9

-A10

-A11

-A12

-A13

-A14

-A15

-A16

J3-A9

-A7

-A6

-A5

-A4

-A3

-A2

-A16

+5V

+5V

Video controller PCB

Connector 1 PCB

Operation panel

Summary of Contents for LBP-1000



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands