Canon LBP-1000 Service Manual Download Page 100

Page: 100 / 178

F. Lower Registration Roller

1) Remove the registration roller unit

according to the steps 1) through 3) on
page 3-8.

2) Remove the 3 springs, and then sepa-

rate the upper registration roller unit
from the registration roller unit.

➀

Springs

➁

Upper registration roller unit

Figure 3-4-7

3) Remove the 2 bushings, gear, and then

the lower registration roller.

➀

Bushings

➁

Gear

➂

Lower registration roller

Figure 3-4-8

G. Registration Shutter

1) Remove the registration roller unit

according to the steps 1) through 3) on
page 3-8.

2) Separate the upper registration roller

unit from the registration roller unit.

3) Remove the 2 bushings from the upper

registration roller unit, and then pull
the shaft to the right to remove.
Remove the registration shutter.

➀

Bushings

➁

Shaft

➂

Registration shutter

Figure 3-4-9

< Note for reassembly >

When attaching the registration shutter to
the shaft, be sure to set the spring secure-
ly.

CHAPTER 3

3 - 13

➁

➂

➀

➁

➂

➀

➁

➀

Summary of Contents for LBP-1000


















































































































































































Search results

Summary of Contents for LBP-1000

Reviews:

Brands by name

Popular brands

Canon LBP-1000, Service Manual

Search results

Summary of Contents for LBP-1000

Reviews:

Brands by name

Popular brands