Canon LBP-1000 Service Manual Download Page 113

Page: 113 / 178

D. Video Controller PCB

1) Remove the options such as RAM,

DIMM, or ROM, if installed.

2) Remove the top cover unit and right

cover.

3) Remove the 3 screws, and then the

memory cover.

➀

Screws

➁

Memory cover

Figure 3-8-7

4) Disconnect the 2 connectors, remove

the 5 screws, and then the video con-
troller unit.

➀

Connectors

➁

Screws

➂

Video controller PCB

Figure 3-8-8

5) Remove the 4 screws, and then the

video controller unit mounting plate.

➀

Screws

➁

Video controller unit mounting plate

Figure 3-8-9

6) Remove the 3 screws. Move the video

controller PCB to the direction of the
arrow to remove the connector and then
the video controller PCB.

➀

Screws

➁

Video controller PCB

Figure 3-8-10

< Note for reassembly >

When installing the video controller unit,
be sure to set the flat cable securely.
If there are options removed, be sure to
reinstall them to where they came from.

CHAPTER 3

3 - 26

➁

➀

➁

➀

➂

➀

➁

Summary of Contents for LBP-1000


















































































































































































Search results

Summary of Contents for LBP-1000

Reviews:

Canon LBP-1000, Service Manual, Page: 113 / 178

Search results

Summary of Contents for LBP-1000

Reviews: