Canon LBP-1000 Service Manual Download Page 175

Page: 175 / 178

APPENDEX

A - 13

Message

Action

Meaning

CONTEXT SAVE

CHANGE

LOAD <SIZE>

IN <TRAY>

LOAD <size>

IN MANUAL

MEM ALLOC

ERROR

RESTORING

DEFAULTS

MR T COMPRES-

SION

TONER CART

MISSING

OPERATION CHECK

PANEL CHECK

DONE

PAGES: ####

not enough memory to support the setup.

The user has pressed Go key to go on-line

after adjusting the context saving feature.

The printer is allocating enough memory for

the context saving feature.

Load the specified tray with the correct

paper size, according to the message.

CASSETTE1: The internal cassette

CASSETTE2: The optional paper feeder

MPT: The Multi-purpose tray

ANY TRAY: Any tray that support Letter-,

Legal-, A4-, A5-, Executive-, or B5-JIS-size

paper.

<size>

LETTER: Letter size paper

LEGAL: Legal size paper

A4: A4 size paper

A5: A5 size paper

EXEC: Executive size paper

COM10: Commercial #10 envelope

MONARCH: Monarch envelope

DL: DL envelope

C5: C5 envelope

B5-JIS: B5-JIS size paper

B5-ISO: B5-ISO envelope

CUSTOM: Paper loaded from the MPT or

manual feed

Any: Unknown paper size

Load Multi-purpose tray with the specified

paper.

There is not enough memory available to

process the data and print the page. If

AUTOCONT is ON (CONFIG MENU), the

print job will resume after 10 seconds.

This message is displayed when the RESET

=MENU is selected in the RESET MENU.

The printer is using MRT Compression, with

the possibility of print quality deration (lossy

compression)

No toner cartridge is installed in the printer,

or the cartridge is not installed correctly.

This is the Control Panel Diagnostic Mode.

Displays during a panel check function.

Displays when panel check function is com-

plete

This message is displayed when SHOW

PAGE COUNT is selected in the TEST

Press Go key to enable the new

setting and resume operation.

The specified paper source must

be loaded with the requested

paper size. To continue the print

job, you may have to press Go

key.

If the paper source runs out of

paper during printing, reloading

the paper source will allow the

printer to continue printing.

For manual feed, you need to

press Go key to continue printing.

Press the Go key to resume print-

ing.

If AUTOCONT is OFF, you must

press the Go key to resume print-

ing. Check the printed page to

ensure that it is complete.

No action required.

Replace the toner cartridge or, if

cartridge is installed, remove it

and insert it again.

For detail, see Chapter 2.

No action required.

Summary of Contents for LBP-1000


















































































































































































Search results

Summary of Contents for LBP-1000

Reviews:

Canon LBP-1000, Service Manual, Page: 175 / 178

Search results

Summary of Contents for LBP-1000

Reviews: