Canon LBP-1000 Service Manual Download Page 45

Page: 45 / 178

c. Abnormal warm-up 2 (initial/print temperature control mode)

The CPU assesses an abnormal warm-up 2 when the temperature does not exceeds the point of
5

C lower than the target print temperature within 75 seconds after starting the supply of power

to the heater.

d. Low temperature during temperature control (print/between-page temperature con-

trol mode)

The CPU assesses a low temperature during temperature control when the detected temperature
is lower than 120

C for 1 second or more continuously in the print/between-page temperature

control mode.

e. Broken thermistor wire (all modes)

The CPU assesses a broken thermistor wire when the output voltage from the thermistor is
about 3.2V or more for 1 second or more continuously.

CHAPTER 2

2 - 11

Summary of Contents for LBP-1000


















































































































































































Search results

Summary of Contents for LBP-1000

Reviews:

Brands by name

Popular brands

Canon LBP-1000, Service Manual

Search results

Summary of Contents for LBP-1000

Reviews:

Brands by name

Popular brands