Canon iR2018 Series, Service Manual

Page: 257 / 348

Chapter 14
14-9
E542 0001 - Optional tray motor or finisher controller PCB failure
- Optional tray HP sensor failure
- Optional tray clock sensor failure
- Optional tray shift motor load failure
The optional tray was operated, but the paper
surface was not detected.
- Check the connector of the optional tray HP sensor.
- Check the connector of the optional tray clock sensor.
- Check the connector of the optional tray shift motor.
- Replace the optional tray HP sensor.
- Replace the optional tray clock sensor.
- Replace the optional tray shift motor.
- Replace the finisher controller PCB.
0002 - Optional tray motor or finisher controller PCB failure
- Optional tray HP sensor failure
- Optional tray clock sensor failure
- Optional tray shift motor load failure
Cannot move (to the pickup position) within the
specified time.
- Check the connector of the optional tray HP sensor.
- Check the connector of the optional tray clock sensor.
- Check the connector of the optional tray shift motor.
- Replace the optional tray HP sensor.
- Replace the optional tray clock sensor.
- Replace the optional tray shift motor.
- Replace the finisher controller PCB.
0003 - Optional tray motor or finisher controller PCB failure
- Optional tray HP sensor failure
- Optional tray clock sensor failure
- Optional tray shift motor load failure
- The optional tray was moved upward, but it did
not reach the HP sensor within 3000 ms.
- Check the connector of the optional tray HP sensor.
- Check the connector of the optional tray clock sensor.
- Check the connector of the optional tray shift motor.
- Replace the optional tray HP sensor.
- Replace the optional tray clock sensor.
- Replace the optional tray shift motor.
- Replace the finisher controller PCB.
0005 - Optional tray motor or finisher controller PCB failure
- Optional tray HP sensor failure
- Optional tray clock sensor failure
- Optional tray shift motor load failure
- The encoder clock signal was not detected two or
more times when the optional tray was operated
for 300 ms.
- Check the connector of the optional tray HP sensor.
- Check the connector of the optional tray clock sensor.
- Check the connector of the optional tray shift motor.
- Replace the optional tray HP sensor.
- Replace the optional tray clock sensor.
- Replace the optional tray shift motor.
- Replace the finisher controller PCB.
E575 0001 - Stack delivery motor or finisher controller PCB failure
- Stack delivery HP sensor failure
- The stack delivery motor was driven for 2000 ms
in the stack delivery direction (HP sensor
approach direction), but the stack delivery HP
sensor did not turn on.
- Check the connector of the stack delivery HP sensor.
- Check the connector of the stack delivery motor.
- Check the connector of the stack delivery HP sensor.
- Replace the stack delivery motor.
- Replace the finisher controller PCB.
0002 - Stack delivery motor or finisher controller PCB failure
- Stack delivery HP sensor failure
- The stack delivery motor was driven for 2000 ms
in the HP sensor escape direction, but the stack
delivery HP sensor did not turn off.
- Check the connector of the stack delivery HP sensor.
- Check the connector of the stack delivery motor.
- Check the connector of the stack delivery HP sensor.
- Replace the stack delivery motor.
- Replace the finisher controller PCB.
E584 0001 - Shutter drive motor or finisher controller PCB failure
- Shutter open detection sensor failure
- Shutter clutch failure
- The shutter open sensor did not turn on when
1000 ms have lapsed since the shutter unit had
performed open operation, resulting in incomplete
open operation.
- Check the connector of the shutter open sensor.
- Check the connector of the shutter clutch.
- Check the connector of the shutter motor.
- Replace the shutter open sensor.
- Replace the shutter clutch.
- Replace the shutter drive motor.
- Replace the finisher controller PCB.
0002 - Shutter drive motor or finisher controller PCB failure
- Shutter open detection sensor failure
- Shutter clutch failure
- The shutter open sensor did not turn off when
1000 ms have lapsed since the shutter unit had
performed close operation, resulting in
incomplete close operation.
- Check the connector of the shutter open sensor.
- Check the connector of the shutter clutch.
- Check the connector of the shutter motor.
- Replace the shutter open sensor.
- Replace the shutter clutch.
- Replace the shutter drive motor.
- Replace the finisher controller PCB.
Display
code
Detail
Code
Main Cause/Symptom Countermeasure