Canon IMAGERUNNER 7095 PRINTER Service Manual Download

Page: 15 / 615

Contents

12.1.8

e-RDS setting screen

.......................................................................................................................... 12- 3

12.1.9

Sleep operation

.................................................................................................................................... 12- 5

12.1.10

Network Setting (Maintenance)

....................................................................................................... 12- 5

12.1.11

e-RDS Setting (Maintenance)

.......................................................................................................... 12- 6

12.1.12

Trouble shoot

...................................................................................................................................... 12- 6

12.1.13

Error message

.................................................................................................................................... 12- 7

Chapter 13 Maintenance and Inspection

13.1

Periodically Replaced Parts

...................................................................................................................... 13- 1

13.1.1

Overview

............................................................................................................................................... 13- 1

13.1.2

Machine Proper

.................................................................................................................................... 13- 1

13.2

Durables and Consumables

...................................................................................................................... 13- 1

13.2.1

Overview

............................................................................................................................................... 13- 1

13.2.2

Machine Proper

.................................................................................................................................... 13- 2

13.3

Scheduled Servicing Basic Procedure

.................................................................................................... 13- 4

13.3.1

Scheduled Servicing Basic Procedure

............................................................................................. 13- 4

13.3.2

Scheduled Servicing Chart

................................................................................................................. 13- 6

13.3.3

Scheduled Maintenance Work Procedure

....................................................................................... 13- 8

13.3.4

Points to Note About Schedule Servicing

...................................................................................... 13- 12

Chapter 14 Standards and Adjustments

14.1

Image Adjustment Basic Procedure

........................................................................................................ 14- 1

14.1.1

Making Pre-Checks

............................................................................................................................. 14- 1

14.1.2

Making Checks on the Printer Side (Checking the Images)

......................................................... 14- 1

14.1.3

Making Checks on the Printer Side (Checking the Density Slope)

.............................................. 14- 2

14.1.4

Making Checks on the Printer Side (Checking the Solid Black Density)

.................................... 14- 3

14.1.5

Making Checks on the Printer Side (Checking for fogging)

.......................................................... 14- 4

14.1.6

Making Checks on the Printer Side (Checking Halftone Density)

................................................ 14- 4

14.1.7

Making Checks on the Reader Unit

.................................................................................................. 14- 5

14.1.8

Potential Control System Conversion Table

.................................................................................... 14- 7

14.2

Image Adjustments

................................................................................................................................... 14- 11

14.2.1

Standards of Image Position

............................................................................................................ 14- 11

14.2.2

Checking the Image Position

........................................................................................................... 14- 11

14.2.3

Adjusting Side Registration

.............................................................................................................. 14- 11

14.2.4

Adjusting the Image Leading Edge Margin

.................................................................................... 14- 13

14.2.5

Adjusting the Left/Right Non-Image Width

.................................................................................... 14- 14

14.2.6

Adjusting the Leading Edge Non-Image Width

............................................................................. 14- 14

14.3

Scanning System

...................................................................................................................................... 14- 14

14.3.1

When Replacing Components of the Scanning System

.............................................................. 14- 14

14.3.2

When Replacing Components of the Scanning System

.............................................................. 14- 14

14.3.3

Adjusting the Position of the No. 1/No. 2 Mirror Base

................................................................. 14- 14

14.4

Laser Exposure System

........................................................................................................................... 14- 16

14.4.1

When Replacing the Laser Scanner Unit

....................................................................................... 14- 16

14.4.2

Checking the Laser Power

............................................................................................................... 14- 16

14.5

Image Formation System

........................................................................................................................ 14- 17

14.5.1

Adjusting the Height of the Charging Wire

.................................................................................... 14- 17

14.6

Fixing System

............................................................................................................................................ 14- 17

Summary of Contents for IMAGERUNNER 7095 PRINTER







































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IMAGERUNNER 7095 PRINTER

Reviews:

Related manuals for IMAGERUNNER 7095 PRINTER

Brands by name

Popular brands

Canon IMAGERUNNER 7095 PRINTER, Service Manual

Search results

Summary of Contents for IMAGERUNNER 7095 PRINTER

Reviews:

Related manuals for IMAGERUNNER 7095 PRINTER

Brands by name

Popular brands