4
4-6
MEMO:
Any of the following error codes may be indicated at time of reception because of line
condition
##0107, ##0114, ##0201
Be sure to change bit 4 before changing this bit; if errors still occur, change this bit.
When 'high speed' is selected, only high-speed signals (images) will be received after
transmission of the CFR signal.
Detailed Discussions of Bit 4
Use it to select the time length during which low-speed signals are ignored after transmission
of the CFR signal.
If the condition of the line is not good and, therefore, the reception of image signals is difficult,
select '1500 ms.'
Detailed Discussions of Bit 5
In the countries that need approval of CI signal frequency check, no checking on frequency
set at PBX when changing the frequency to PSTN setting and PBX
setting for frequency checks.
Detailed Discussions of Bit 6
Selects whether or not to transmit CNG signal during manual transmission.
In manual transmitting to a fax with the FAX/TEL switching mode, if there are frequent errors
due to failure to switch to fax mode, select "Transmitted" for the CNG signal.
Detailed Discussions of Bit 7
Selects whether or not to transmit CED signals during manual reception. If the other fax does
not transmit even when you start manual reception, select "Transmitted" for the CED signal.
SSSW-SW05
List of Functions
Bit
Function
1
0
0
not used
-
-
1
Conversion from mm to inch (text mode)
execute
do not execute
2
Conversion from mm to inch (text/photo mode)
execute
do not execute
3
transmit bit 33 and thereafter for DIS signal
prohibit
do not prohibit
4
Recording paper length availability declared in
DIS signal
A4 /B4 size
Arbitrary size
5
not used
-
-
6
not used
-
-
●
Bit
Function
1
0
7
not used
-
-
Detailed Discussions of Bit 1
Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read
in text mode.
Scanning direction in conversion follows the Bit 2 setting of SW14.
Detailed Discussions of Bit 2
Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read
in text/photo mode while bit 1 is set to '1'.
Scanning direction in conversion follows the Bit 2 setting of SW14.
Detailed Discussions of Bit 3
Use it specify whether or not to transmit bit 33 and thereafter for the DIS signal.
If ‘prohibit’ is selected, Super Fine reception from a non-Canon machine can no longer be
used.
CAUTION:
If ‘prohibit’ is selected, Super Fine reception from a non-Canon machine
can no longer be used.
Detailed Discussions of Bit 4
Selects whether or not the recording paper length declared in the DIS signal is A4 size.
When receiving documents made up of long pages, to have the document divided into two
pages at the transmitting fax, select “A4 size”.
MEMO:
When “A4 size” is selected, this fax uses the DIS signal to tell the transmitting
fax that it is equipped with A4 size recording paper.
The transmitting fax that receives this DIS signal divides long pages into A4 size pages
before transmitting it to the receiving fax.
Some fax models do not so divide long documents.
T-4-6
T-4-6
Summary of Contents for IMAGERUNNER 2530
