Canon imageRUNNER 2420 Trouble Error Codes List Download Page 12 | Manualshive

Page: 12 / 30

Canon imageRUNNER 2420 Trouble Error Codes List Download Page 12

12

Code

Description

Remedy

E225-
0002

The light intensity of the CIS is faulty.
During DF stream reading, the sheet-to-
sheet light intensity is faulty.

Disconnect and then connect the flexible
cable. Replace the following as necessary:
flexible cable, CIS, reader controller PCB.

E227-
0001

The reader unit power supply is faulty.
At time of power-on, the 24-V port is off.

Disconnect and then connect the power
supply harness connector. Replace the power
supply.

E227-
0002

The reader unit power supply is faulty.
At the start of a job, the 24-V port is off.

Disconnect and then connect the power
supply harness connector. Replace the power
supply.

E227-
0003

The reader unit power supply is faulty.
At the end of a job, the 24-V port is off.

Disconnect and then connect the power
supply harness connector. Replace the power
supply.

E227-
0004

The reader unit power supply is faulty.
When a load is being driven, the 24-V
port is off.

Disconnect and then connect the power
supply harness. Replace the power supply.

E248-
0000

The backup memory is faulty.
[Cause] A check error has occurred on
the backup SRAM board. [Location]
bottom ROM [Timing of Detection] once
when the boot ROM is started up

1. Check the presence/absence of a backup
SRAM PCB. 2. Disconnect and then connect
the backup SRAM PCB. 3. Replace the
backup SRAM PCB with a new one.

E248-
0001

The backup memory is faulty.
An error has occurred at power-on.

Replace the reader controller PCB.

E248-
0002

The backup memory is faulty.
An error has occurred during a write
operation.

Replace the reader controller PCB.

E248-
0003

The backup memory is faulty.
An error has occurred during a read
operation following a write operation.

Replace the reader controller PCB.

E261-
0000

The zero-cross signal is faulty.
When the relay is on, the zero-cross
signal is not detected for 500 msec or
more.

Replace the AC driver PCB. Replace the DC
controller PCB.

E315-
0007

There is an error in image data.
There is an error in JBIG encoding.

Turn off and then back on the power.

E315-
000d

There is an error in image data.
There is an error in JBIG decoding.

Turn off and then back on the power.

E400-
0001

DF communication error
Check sum error

Disconnect and then connect the connector.
Replace the reader controller PCB. Replace
the ADF controller PCB.

E400-

DF communication error

Disconnect and then connect the connector.

«
...
10
11
12
13
14
...
»

Summary of Contents for imageRUNNER 2420































Reviews:

No comments