Canon imagePRESS Server M10 Page 26 Service Manual Download

Page: 26 / 98

8. Check the 10-pin power button cable that connects the printer interface board (J351) and the motherboard (J11).

Make sure that the cable is intact.
The following diagrams illustrate the internal cable connections between hardware components and the motherboard.

Figure 8:

imagePRESS Server

internal cable connections

No.

Name

HDD

Power supply

Chassis fan

CPU fan

No.

Cable key

From

Power supply cables

Power supply

a. SATA power connector-HDD
b. 4-pin power connector (PWRCONN1)
c. 24-pin power connector (J24)

10-pin power button cable

Printer interface board (J351) J11 connector on motherboard

HDD data cable

HDD data connector

SATA0 connector on motherboard

Service board cable

Service board connector

Port 80 Header (EFI GPIO Header) connector on mother-
board(J4)

CPU fan cable

CPU fan

CPUFAN connector on motherboard (CPU FAN J16)

Chassis fan cable

Chassis fan

FRONT FAN connector on motherboard (J30)

Removing and replacing imagePRESS Server components

Before replacing costly components, be sure to verify the connections between the printer and the

imagePRESS Server

. Also,

verify the connections of each replaceable

imagePRESS Server

component. For more information about troubleshooting, see

“5. TROUBLESHOOTING” on page 67

The following sections describe how to remove and install replaceable parts on the

imagePRESS Server

• Printer interface board
• DIMM
• Battery
• Motherboard

3. REPLACING PARTS

Summary of Contents for imagePRESS Server M10


































































































Search results

Summary of Contents for imagePRESS Server M10

Reviews:

Related manuals for imagePRESS Server M10

Brands by name

Popular brands

Canon imagePRESS Server M10, Service Manual

Search results

Summary of Contents for imagePRESS Server M10

Reviews:

Related manuals for imagePRESS Server M10

Brands by name

Popular brands