Canon imagePRESS Server M10 Page 71 Service Manual Download

Page: 71 / 98

A message appears that indicates that the installation has started.

NOTE:

After confirming the LED activity starts and the LED display shows the cyclic codes (C1 > C2 > C3 > C1...), turn off the printer
using the main power switch on the front.

Once the installation is complete, the

imagePRESS Server

will shut down automatically.

13. Flip both of the

imagePRESS Server

service switches to the Normal (OFF) position.

Figure 32: Flipping the

imagePRESS Server

service switches

No.

Name

Flip the service switches from Service (ON) position...

...to Normal mode (OFF) position.

14. Disconnect the Ethernet cable from the

imagePRESS Server

network port and the Windows computer.

15. Reconnect all the cables that were connected to the

imagePRESS Server

4. INSTALLING SYSTEM SOFTWARE

Summary of Contents for imagePRESS Server M10


































































































Search results

Summary of Contents for imagePRESS Server M10

Reviews:

Related manuals for imagePRESS Server M10

Brands by name

Popular brands

Canon imagePRESS Server M10, Service Manual

Search results

Summary of Contents for imagePRESS Server M10

Reviews:

Related manuals for imagePRESS Server M10

Brands by name

Popular brands