manualshive.com logo in svg

Canon Color imageRUNNER LBP5280, Service Manual, Page: 235 / 284

Share
Download
Canon Color imageRUNNER LBP5280 Service Manual Download Page 235

5

5

5-38

5-38

Troubleshooting > Version Upgrade > Updater > b. UGW-linked Download (Remote Distribution Update)

Troubleshooting > Version Upgrade > Updater > b. UGW-linked Download (Remote Distribution Update)

 

■

a. UGW-linked Download and Update (Full-remote Update)

See the figure below for the operational flow of “UGW-linked Download and Update”.

STEP 1

Scheduling

via UGW

STEP1: Scheduling via UGW

The firmware distribution schedule to the certain device should be set on UGW.
See “UGW-linked Download and Update” in Operation Manual of Content Delivery System for 
Firmware Distribution for details.
The device checks the schedule concerned every 12 hours on UGW. This allows the device 
to register the firmware distribution setting, enabling automatic firmware download and 
update.

CAUTION:
[Device without the function to wait for job completion]
•  Explain to the user in advance that a job cannot be accepted during firmware update. 

Also, it is recommended to execute the operation during the period of time when no 
print job is accepted.

[Device with the function to wait for job completion]
•  When the following jobs exist at the time of firmware update, firmware update 

processing is not executed until job completion.

- Printing 
- I-FAX 

NOTE:

To contacts registered for E-mail notification on UGW, the E-mail is sent from UGW 

upon completing firmware update.

F-5-51

 

■

b. UGW-linked Download (Remote Distribution Update)

See the figure below for the operational flow of “UGW-linked download”.

STEP 2

Update using 

Updater

STEP 1

Scheduling

via UGW

STEP 1: Scheduling via UGW

The firmware distribution schedule to the certain device should be set on UGW.
See “UGW-linked Download” in Operation Manual of Content Delivery System (for Firmware 
Distribution) for details.

NOTE:

The firmware downloaded by scheduling via UGW can be checked/deleted from User 

mode, but cannot be updated. If a user download the other firmware, the firmware 

downloaded with "UGW-linked Download" is overwritten.

STEP 2: Update using Updater

The firmware downloaded on the device can be updated using Updater functions.

1) Enter service mode. Select [F/W UPDATE].

2) Select CDS.

F/W UPDATE GR.

CDS

USB STORAGE

USB

NETWORK

F-5-52

F-5-53

Summary of Contents for Color imageRUNNER LBP5280





























































































































































































































































































Reviews:

No comments