background image

  

OWNER’S MANUAL 

CAUTION:  
READ THIS MANUAL CAREFULLY 
BEFORE OPERATING YOUR NEW 
CANNON

®

 DOWNRIGGER. 

RETAIN FOR FUTURE REFERENCE. 

Introduction to Downriggers  

pg. 2 

Mounting Your Downrigger  

pg. 2-6 

Terminator & Line Release  

pg. 7 

Cannon Uni-Release 

pg. 7 

Attaching the Rod Holder 

pg. 8 

Wiring Your Downrigger  

pg. 8-9 

Powering Multiple Downriggers  

pg. 10 

Installing Optional Transducer  

pg. 11 

Operating & Programming  

pg. 12-17 

Fishing with your Downrigger  

pg. 18 

Positive Ion Control  

pg. 18 - 19 

Maintaining Your Downrigger  

pg. 19 

The Effects of Blowback  

pg. 20 

Troubleshooting  

pg. 21 

Trolling Tips  

pg. 22 

Warranty Information  

pg. 23 

Cannon Service Policy  

pg. 23

  

Authorized Service Centers  

See List

 

Digi-Troll IV 

 

NOTE: Do not return your CANNON® Downrigger to your 
retailer. Your retailer is not authorized to repair or replace this 
unit. You may obtain service by: 

• 

calling CANNON® at 1-800-227-6433; 

• 

returning your downrigger to the Factory Service Center; 

• 

sending or taking your downrigger to any CANNON® 
Authorized Service Center on enclosed list.  

Please include proof of purchase, serial number and purchase 
date for warranty service with any of the above options.  

AnglingOutpost.com

1-888-356-5022

AnglingOutpost.com

1-888-356-5022

Summary of Contents for Digi-Troll IV

























Reviews: