Canmax CM-2D202 Page 12 User Manual Download

Page: 12 / 240

1. GET STARTED

1-3 Reset the Custom Defaults

If you want the custom default settings restored to your scan engine, scan the

Activate Custom Defaults bar code below.

This is the recommended default bar code for most users. It resets the scan

engine to the custom default settings.

If there are no custom defaults, it will reset the scan engine to the factory

default settings.

Any settings that have not been specified through the custom defaults will be

defaulted to the factory default settings.

Activate Custom Defaults

Note

: To remove cutom defaults, see

"Resetting the Factory Defaults".

1-3 Reset the Custom Defaults

Summary of Contents for CM-2D202
















































































































































































































































Search results

Summary of Contents for CM-2D202

Reviews:

Related manuals for CM-2D202

Brands by name

Popular brands

Canmax CM-2D202, User Manual

Search results

Summary of Contents for CM-2D202

Reviews:

Related manuals for CM-2D202

Brands by name

Popular brands