Canmax CM-2D202 User Manual Download

Page: 32 / 240

PROGRAM THE INTERFACE

2-7 Keyboard Modifiers

This modifies special keyboard features, such as CTRL+ ASCII codes and

Turbo Mode.

C X (C ASCII) Mode On

: The scan engine sends key

combinations for ASCII control characters for values 00-1F. Windows is the

preferred mode. All keyboard country codes are supported. DOS mode is a

legacy mode, and it does not support all keyboard country codes. New users

should use the Windows mode. Refer to

ASCII Conversion Chart (Code Page

1252)

for CTRL+ X Values.

Windows Mode Prefix/Suffix Off

: The scan engine sends key combinations

for ASCII control characters for values 00-1F, but it does not translate any

prefix or suffix information.

Default = C X Mode Off.

Windows Mode C X Mode On

C X Mode Off

DOS Mode C X Mode On

Windows Mode Prefix/Suffix Off

2-7 Keyboard Modifiers

Summary of Contents for CM-2D202
















































































































































































































































Search results

Summary of Contents for CM-2D202

Reviews:

Related manuals for CM-2D202

Brands by name

Popular brands

Canmax CM-2D202, User Manual

Search results

Summary of Contents for CM-2D202

Reviews:

Related manuals for CM-2D202

Brands by name

Popular brands