Canmax CM-2D202 User Manual Download

Page: 52 / 240

INPUT/OUTPUT SETTINGS

3-5 Manual Trigger Mode

When in manual trigger mode, the scanner scans until a bar code is read, or

until the trigger is released.

Manual Trigger - Normal

3-5-1 LED Illumination - Manual Trigger

If you wish to set the illumination LED brightness, scan one of the barcodes

below. This sets the LED illumination for the scan engine when the trigger is

pressed.

Default = High

Note: The LEDs are like a flash on a camera. The lower the ambient light in the

room, the brighter the LEDs need to be so the scan engine can “see” the bar

codes.

Low

High

3-5 Manual Trigger Mode

3-5-1 Illumination – Manual Trigger

Summary of Contents for CM-2D202
















































































































































































































































Search results

Summary of Contents for CM-2D202

Reviews:

Related manuals for CM-2D202

Brands by name

Popular brands

Canmax CM-2D202, User Manual

Search results

Summary of Contents for CM-2D202

Reviews:

Related manuals for CM-2D202

Brands by name

Popular brands