Canine Innovations Invisible Fence ICT 801 Installation Manual Download Page 23

23 

 

1.

 

Position the collar strap unit high on the pet’s neck with the Computer Collar

®

 unit 

under its lower jaw.  

 

2.

 

To avoid having a collar that is too tight on a thick-haired pet; thin some hair away to 

make skin contact with the correction posts. DO NOT shave the pet’s neck.  

 

3.

 

Tighten the strap of the Invisible Fence

®

 Brand Computer Collar

®

 unit appropriately. 

Adjust the collar so it is snug enough to slide one finger between the correction post 

and the pet’s skin.  

 

4.

 

The fit of the Invisible Fence

®

 Brand Computer Collar

®

 unit should be adjusted as 

necessary as the pet’s coat, weight, and age change. The pet’s coat may change from 

season to season. 
 

IMPORTANT:  

Allow the pet to become accustomed to 

its new Invisible Fence

®

 Brand 

Computer Collar

®

 unit. The collar 

should be removed each night during 

the first month of training and 

regularly thereafter. This ensures 

proper fit and avoids the possibility of 
skin irritation from the correction 

posts. 

 

 

Power Cap

®

 Unit Status: 

 

This Computer Collar

®

 unit monitors Power Cap

®

 unit status and will alert the owner when 

the Power Cap

®

 unit needs to be replaced.  

 

LED Status Indicator          

 

 

 

 

When the Power Cap

®

 unit is first inserted, the LED Status Indicator shows a GREEN light 

for up to 1 second while testing. After that, you will see 4 blinks in one of the following 
colors, indicating the Power Cap

®

 unit status: 

Summary of Contents for Invisible Fence ICT 801




























Reviews: