background image

20 

 

a. For ICT 801: The L1 Freq. LED begins to blink.  

b. For ICT 802: The Loop 1 LED begins to blink. 

2. Release the S1 button. 
3. Momentarily press and release the S2 button to toggle between each setting option. 

4. Press and release the S1 button to move to the next setting. 

5. Continue until all choices are selected. 

6. The cursor LED will stop blinking approximately ten seconds after the buttons are 
released, and the transmitter will automatically exit the programming mode. 

 

 

IMPORTANT: If the transmitter is disconnected from the power source while the 

system indicator lights are still blinking, the settings will not be saved to system memory. 
 
                                                                     

Audible Alarm: There is an audible alarm for certain alert conditions (See table below). 

Press and release either the S1 or the S2 button on the circuit board to silence the alarm. 

The alarm will re-activate on power-up, or when exiting set-up mode (if a failure condition 

still exists). 
 

LED Status Indicator Light 

 

 
 

Primary Power 

Primary power to the unit shall be provided by: 

ICT 801 Transmitter: AC Adapter Model RAC00-12612 (Universal transformer) 
 
Setting the Signal Field Width 

 

The signal field is what activates the Computer Collar

®

 unit. The edge of the signal field can 

be set to various distances from the signal field wire. The distance from the wire loop to the 
edge of the signal field is called the signal field width. 

 

Summary of Contents for Invisible Fence ICT 801




























Reviews: