10 GB
SERVICE CENTRE
Before calling the Service Centre
If the oven is not working, we recommend that:
• you check that the oven is properly plugged into the power
supply.
If the cause of the fault cannot be detected:
disconnect the oven from the mains, do not touch the oven and
call the after sales service.
Before calling the Service Centre remember to make a note
of the serial number on the serial number specifications plate.
The oven is supplied with a guarantee certificate that ensures that
it will be repaired free of charge by the Service Centre whilst
under guarantee.
This appliance is marked according to the
European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product indicates that this
product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point
for the recycling of electrical and electronic equipment
Disposal must be carried out in accordance with local
environmental regulations for waste disposal.
For more detailed information about treatment, recovery and
recycling of this product, please contact your local city office,
your household waste disposal service or the shop where you
purchased the product.
CLEANING THE OVEN : PYROLYSIS
- according to the model -
Pyrolysis is a cleaning method that uses high temperatures to
destroy dirt.
The resulting smoke is cleaned by the passage of a catalyser.
The oven door is provided with a safety lock that prevents it being
opened during pyrolysis due to the necessity of high temperatures.
The pyrolysis cycle may result in a slight odour in the kitchen
which will be more or less noticeable depending on the latter’s
aeration.
IMPORTANT:
Before carrying out pyrolysis:
• Take all accessories out of the oven as
they will be damaged
in the high pyrolysis temperatures;
• Clean away all excess food spills or large scraps of food
which would take too long to be destroyed.
Effectively, large
amounts of grease may catch fire under the intense heat
emitted by pyrolysis.
• Close the oven door.
. If you have an hob top installed above the oven, never use
the gas burners or the electric plates during pyrolysis to
avoid excessive heating of the oven’s control panel.
. It is strongly advised not to use detergents or any other
recommended product for cleaning ovens.
•
Open the oven door.
Pyrolysis leaves a white residue on the oven walls.
Wait for the oven to cool completely then clean the inside of the
oven with a damp sponge to wipe off the residue.
Remarks:
•
you will save energy by cleaning directly after cooking thus
making use of the residual heat in the oven.
The pyrolysis oven is fitted with a cooling fan which protects the
c o n t r o l p a n e l a n d e l e c t r o n i c s f r o m h e a t d a m a g e .
It begins when the pyrolysis cycle reaches high temperatures and
continues to rotate after the oven has been switch off until the
centre oven temperature is high.
Activating the pyrolysis cycle
1.
Rotate the function selector to the position P.
On the display, appears the indication “Pyro”.
2. The preset time is 1.30 hrs
, this can be varied from 1.30 hr
to two hours via the programmer (buttons B+ E or F). If the
oven is very dirty it is recommended to increase the time to
2 hrs., if the oven is moderately dirty reduce the cleaning cycle
time to 1:30 hr.
3.
It is possible to defer the start time of the pyroclean cycle by
changing the END time via the programmer (buttons C + F)
4.
Confirm the setting by pressing the button A on the programmer
–
WARNING: THE CLEANING CYCLE WILL NOT START
UNLESS THE CONFIRM BUTTON A HAS BEEN PRESSED.
On the display, appears the symbol .
5.
The pyroclean cycle can be stopped at any time by turning the
function selector back to ‘0’ (the word OFF will be displayed for
3 seconds)
6.
After a few minutes, when the oven reaches high temperature,
the door is locked.
7.
Once the pyro cycle parameters have been set and confirmed
it is not possible to modify them. To change it is necessary to
start from the beginning by cancelling the cycle ( turn selector
to ‘0’ and ‘OFF’ will appear for 3 seconds ) and start again from
point 1.
8.
Once the pyroclean cycle is finished, the pyrolysis will switch
off automatically.
On the display appears the indication until the door
is locked then the indication .
9.
You can turn the function selector back to “0” but if the
temperature is still high, the indication appears
to inform that the door is locked.
:
Summary of Contents for FFN403
Page 2: ......
