Candy CMGN 6184WN, User Manual, Page: 36 / 366

35
• It’s suggested to set the temperature at
4°C in the fridge compartment, and, whether
possible, at -18°C in the freezer compartment.
•
For most food categories, the longest
storage time in the fridge compartment is achieved
with colder temperatures. Since some particular
products (as fresh fruits and vegetables) may be
damaged with colder temperatures, it is suggested
to keep them in the crisper drawers, whenever
present. If not present, maintain an average setting
of the thermostat.
•
For frozen food, refer to the storage
time written on the food packaging. This storage
time is achieved whenever the setting respects the
reference temperatures of the compartment (one-
star -6°C, two stars -12°C, three stars -18°C)
ENERGY SAVING
For better energy saving we suggest:

Installing the appliance away from heat
sources and not exposed to direct
sunlight and in a well-ventilated room.

Avoid putting hot food into the
refrigerator to avoid increasing the
internal temperature and therefore
causing continuous functionalizing of
the compressor.

Do not excessively stuff foods so as to
ensure proper air circulation.

Defrost the appliance in case there is ice
to facilitate the transfer of cold.

In case of absence of electrical energy, it
is advisable to keep the refrigerator
door closed.

Open or keep the doors of the appliance
open as little as possible.

Avoid adjusting the setting to
temperatures too cold.

Remove dust present on the rear of the
appliance.
TAKE CARE
Defrosting
This appliance has automatic defrosting system, no
need to defrost by hand.
Cleaning and Care
After defrosting you should clean the Fridge/Freezer
internally with a weak solution of bicarbonate of
soda. Then rinse with warm water using a damp
sponge or cloth and wipe dry. Wash the baskets in
warm soapy water and ensure they are completely
dry before replacing in the Fridge/Freezer.
Condensation will form on the back wall of the
Fridge; however it will normally run down the back
wall and into the drain hole behind the salad bin.
The drain hole will have a “cleaning spike” inserted
into it. This ensures that small pieces off food can
not enter the drain. After you have cleaned the
inside of your Fridge and removed any food residues
from around the whole, use the “cleaning spike” to
make sure that there are no blockages. Use standard
furniture polish to clean the Fridge/Freezer exterior.
Make sure that the doors are closed to prevent
polish getting on the magnetic door seal or inside.
The grille of the condenser at the back of the
Fridge/Freezer and the adjacent components can be
vacuumed using a soft brush attachment.
Do not use harsh cleaners, scouring pads or solvents
to clean any part of the Fridge/Freezer.
CHANGING THE INTERNAL LIGHT
1. Before carrying out the LED replacement
always disconnect the mains supply.
2. Hold and lift up the LED light cover.
3. Remove the old LED by unscrewing it in an
anti-clockwise direction.
4. Replace with a new LED light by screwing it in a
clockwise direction marking sure that it is
secure in the light holder.
5. Refit the light cover and re-connect your
Fridge to the mains supply and switch on.
REVERSING THE DOOR SWING
Dissemble the Refrigerator Door
1. a
．
Use a tool to remove the screw off the
hinge cover, and then remove the latter. Insert
the communication line to the hole on the
cabinet top.
b
．
Use a tool to remove the 4 screws off the
upper hinge cover and then remove the latter.
Pry up the door bush and small end cap cover
on the door.
c
．
Insert the door bush and door
communication line into the hole on the door
and then put on the small end cap cover.
d
．
Use a tool to remove the 2 screws as
shows in the below figure to remove the hole
cover on the cabinet top and get the cabinet
communication line out of the hole.
Pry up the small end cap cover on the door
and get out the door bush and door
communication line.
e
．
Insert the door bush into the round hole
on the door and then put on the small end cap
cover.
f
．
Move the refrigerator door upward over
500mm to remove the door.
2. a
．
Use a tool to remove the 3 screws off
the middle hinge cover and then remove the
middle hinge.
b
．
move the freezer door upward over
500mm to remove the door.
c
．
Remove the adjustable front feet under
the lower hinge; use a tool to remove the 4
screws from the lower hinge and then
disassemble the lower hinge. Door disassembly
is finished.
Assemble door, lower hinge
accessories to the corresponding
positions
1. a
．
Use a tool to get the door bush out as
36 / 366